I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi
I am using the light controller and added zb_nlme_permit_joining_request to allowing devices to join the network.
I get a good ZB_ZDO_SIGNAL_DEVICE_ANNCE signal and...
In mesh2.1.1\examples\light_switch\proxy_server I find this flash_manager.c file.Its purpose is to store/resorre/remove DSM&access data.
My flash function referred to access...
Dear Team,
I hope you are doing good......
i am using nrf51822 Device, the SDK version is 12.3.0 in the windows pc with keil version 5.26.
Here i am planning to send...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Hi everyone!
I have BMD-300 Series Evaluation kit featuring the nRF52832 and dongle(nrf52840).
I want to use ‘ComPortMaster’ program to process the received data via...
Hi,
I am Using NRF52840-DK. I merged the UART Example code (PCA10056) into the nRFX_SPIM (PCA10056) example code. That compile successfully I want to print a simple statement...
I use SDK15.0
I found nrf_ecb_init(),nrf_ecb_set_key() and nrf_ecb_crypt(),this is an encryption. I didn't find the decryption of nrf52832.
nrf52832 support AES ECB encryption...
Hello.
We are struggling that we can't analysis contents of a encrypted packet during connection mode in BLE communication because of no idea to get a passkey, although...
Hello Nordic, I am a new developer in Korea.
So, I am not good at English yet. Please understand.
The chip I am using now is nRF52832.
The development tool I am suing...
Hello. The project that I'm working requires both central and peripheral role support, working simultaneously. There are times where, while advertising in the peripheral,...
Assigning Pin 0.06 as SPI clock on NRF52840 does not work. Is there any limitation on pins which can or cannot be assigned as clock for SPI. This is important to know because...
I have been playing with the BLE peripheral examples. It seems like most of these examples have LED1 blinking at a rate of once every 2 seconds. I am trying to look for the...
For my application I need to know (within a millisecond or so) when an advertisement has been received. In my testing so far, it looks like there can be significant latency...
Hi
I'm using a NRF52840 as multi central with 8 connections
SDK: 15.0; SD: 6.1 S140
My central connects to a peripheral with a connection interval of 50ms and latency...
Hi All,
i am stuck in SPI2 enable. i am using sdk 14.2 for our design in previous i am using sdk 12.0
i am simply follow these steps in 14.2 and 12.0 to enable spi2. ...
