I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Dear Nordic,
I would like to implement on server side Private Resolvable address according to specs. For that I need to get the IRK that has been sent to client (central...
Can't seem to find the proper sdbc file and pack for the newest version of 51422_S210_256k for Keil 5 on either Keils site nor Nordic's. Called Keil and was told that Nordic...
In Nordic\nrf51822\Board\pca10001\s110\ble_app_hrs project,when I add somting into this project but the now that I add dose not work!!?
//this is buzee_gpiote_init()
static...
Hi,
I am working on proximity solution app and I have to implement link loss and immediate alert service but don't know how implement it as I am a learner in this technology...
Hello
I think my question is pretty simple but I would like to clarify this topic, please:
I have read in other threads in this forum that " bonding should eliminate the...
Hello,
Actually, I am evaluating the nRF51822 using the EK. I have some questions as follows:
1- Is the S120 an enhanced version of the S110, and what is the real difference...
I use P0.2 as a wake-up pin, when the system into a deep sleep, I connected a High Voltage in the P0.2, it can wake up, but if I connected a High Voltage in the P0.2 always...
Hi
I got some questions about the RF part of the ref schematic.
1, why the bias voltage for ANT1 anf ANT2 are not the same since they are differential lines?
2, what...
Hi,
Today I use the app timer to start a simple 8bit ADC conversion each second and send in the irq handler.
Now I am trying to use the sw interrupt to execute some...
Hi
I want a 1K Hz square waveform to drive a peripheral device, but I can not get a continuously square waveform on GPIO 19, pls have a look at the picture I attached,...
Hi All
I am facing one issue using app_timer.c, When I put the PRESCALER value as 327 and started timer as app_timer_start(timer_ID, 100, NULL);, It was giving only 920ms...
Hi,
I ran the Nordic nrftoolbox on Sony Z1 android 4.3. I found that the device name is not showing on the list as attached. Running the Nordic nrftoolbox on Samsung S4...
Hi there,
We are using the nrf8001 and a arduino to read out two sensors.
The two measurements should be at the same time and therefore are coupled to eachother.
Is there...
Hi
I try to program my custom board using J-flash and Flasher ARM ( for production ).
Attached my J-flash configuration.
Connection with device is successful established...
