Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Is the nRF52840-CKAA port impedance for the various transmit power settings (or at least for 8dBm) available?
Alternatively, is the expected port impedance, when viewed...
Hello,
I am building basic board on nRF5340(based on Raytac MDBT53 module) and after "Erase" operation in nRF Connect Programmer I cannot access chip anymore.
Board...
Hi all,
I am working on Fantel BT40F which uses nrf 5340 soc. I have finished my breadboard testing phase with the development kit and now I am working on Integrated pcb...
Before adding ubxlib module repo into nrf/west.yml, I can build any project with mcuboot with no problem.
However, I cannot build any project with mcuboot after adding the...
Hi,
I'm stuck in the loop of calibration. This is the error that I get from Putty:
It says that I get a TX error.
This is the code that I have for bno055.h:
This...
I used C:\ncs\v2.6.1\zephyr\drivers\adc as an example for testing adc, the following code has been added to nrf9160dk_nrf9160_ns.overlay
I applied voltage to pins p0.13...
I'm trying to test the RGB led on the thingy53.
Using the sample: C:\ncs\v2.6.0\zephyr\samples\basic\rgb_led which gives errors about the devices error: '__device_dts_ord_DT_N_ALIAS_red_pwm_led_P_pwms_IDX_0_PH_ORD...
HI currently i am using nrf52840 s140 sdk ver 17.1.0 and have added buttonless dfu in the central uart application after running we got run time error and we followed the...
Hi,
I am migrating from nRF51 to nRF52810 and I am trying to set Debug because its not working in Keil5.
I use PCA10028 board and I am connecting my beacon to P20 port...
I have a nRF9160DK board that is used for development of a custom nRF9160 board. The hardware designers have assigned GPIO P0.27 to be a general purpose output pin. This pin...
NCS 2.3.0
nrf5340dk_nrf5340_ns -- problem is in non-secure domain for an app built with TFM.
I have this in my nrf5340dk_nrf5340_cpuapp_ns.overlay:
at compile time...
Hi, I'm currently getting familiar with mcuboot and DFU
First of all, thank you very much for the new Academy course that covers DFU!
If I understand correctly, to enter...
I am trying to get MCUBOOT working with project based on the Audio_DK base, where we need to do firmware update over UART/Serial interface.
I have added the following...
I am using nRF5 SDK v17.1.0.
Is it possible to connect a peripheral device by MAC address, and the device is advertising with a different UUID from the central device? ...
I am using LittleFS for an external NAND flash by using the KCONFIG option CONFIG_FILE_SYSTEM_LITTLEFS = y and managing the driver implementation manually. This has worked...