Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hello and thanks for reading. I am working with the NRF5340DK and Zephyr (SDK 2.5.0).
As our project has grown, we can no longer fit all our code and MCU boot in the internal...
There are receivers and repeaters with nRF52832 mounted on the board.
When updating with DFU from iPad, a version check error occurs in the customer's environment.
The...
My lipo battery is at 3.86V and I measured 3.76V at VOUT2 which supplies the nRF52832. I just based the design in the example circuits in nPM1300 datasheet. I already reviewed...
Hi Team,
We are using nRF9160
We are provisioning our devices to nRF cloud for more then a year now with a script that create CSV and upload it to cloud during manufacturing...
Hello,
I'm using iphone 15 and nRF52840 board, working on Lesson 3 Exersise 1 solution. In the step 5 after reseting the board there is no logout info on the terminal. But...
HI
When working on the NVS sample on a nrf9160 DK , I noticed the option CONFIG_REBOOT=y
However, it is not clear to me why this option is selected in this sample and...
Hi,
I'm a bit confused regarding the DFU process for the nRF5340: Under what conditions would the interface between the application core and the network core change?
I...
I am using the Nordic Semiconductor Power Profiling Kit II to measure the interval time of a periodic activity of a target device by monitoring the power consumption and measuring...
Our system has SPI and I2C. Each of these communications works in isolation, as implemented in our program, for multiple transactions. When we try to include both we noted...
On p. 62, section "5.3.10.1 Device startup times" of nRF52805 Product Specification v1.4, the startup time of the nRF52805 is discussed as a function of the capacitance to...
Hello,
We use nrf-connect-sdk v1.9.1 (Zephyr v2.7 LTS)
We have a set of network devices. Both routers as sleepy-end-devices.
The sleepy-end-devices connect to the...
how to set bt tx power in NCS
I referred to this example "hci_pwr_ctr", but err occurs:"Set Tx power err: -5 reason 0x00", Possible errors are BT_SCI-ERR_SUNKNOWN_CMD。 ...
Running NRF52840 mcu core on custom board using 17.1 SDK
1. Use the nRF Connect Mobile app to connect to our device over BLE
2. Run the dfu uploader to update FW from...
I am planning to modify the SLM application (NRF9161) to load its own certificates for TLS upon startup. This should be doable via modem_key_mgmt functions.
However, NRF5340...
