I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi,
I'm creating a new ticket for a questions asked a few years ago:
I'm in the process of also developing an app to send some data I've collected from nRF Cloud to Android...
Hello. I'm completely new to nRF cloud. now my iot device is successfully sending the data to the nRFcloud.
now i'm building an android app and i don't know how to get that...
When i call the custom-code certify() function inside my code in a secure partition i can build the programm, but after clicking flash/running the secure uart-output prints...
Is there a DTM sample for the nrf52dk_nrf52832?
I see the sample supports nRF52840 and higher according to the docs.
I tried selecting the nRF52dk, and everything compiles...
Hello,
As the LE Audio controller for nRF5340 library is deprecated in favor of the Nordic Semiconductor’s standard Softdevice Controller. We have started to use the Softdevice...
Hi, am using the nrf52dk with nrf52832, nrf coonect sdk 2.5.1/ toolchain 2.5.2 and am building a prototype to aquire the signal from the ckp and cmp sensor in the car when...
Using the official nRF Connect for VS Code extension sometimes when debugging and hitting a fatal error, no backtrace is shown (backtrace seems to be mostly garbage):
...
Hi,
As well know, there have a nrf_delay_us() function can execute very short delay time, but the function can only "delay".
If I want to create a 1 microsecond continuous...
How are the 28-UFBGA pin assignments translated to numbering used to specify I/O pin numbers in the code. Is this as simple as P0.0 => 0, P0.1 => 1,...? I have seen similar...
software:ncs2.5.1
chip:nrf5340
hi professor,
I want to use dtm to test blue RF. After i compile dtm example by vs code and download merge.hex by nrf connect sdk programmer...
Hello,
I am experiencing an issue where ble_nus_data_send returns a value of 0x08. I would appreciate any advice on how to resolve this error.
Symptoms: The device ...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0 ]
I used UART for communication between...
This is my log output when i connect to my ethernet
this is my prj.conf file
I am building the default AWS_IOT_MQTT SAMPLE. i dont know where i am getting the issue...
I want to implement a network of boards to be placed in a field. We have sender nodes(boards) which will collect data through saadc channels and transmit it to receiver node...
Hello,
i am developing a bootloader with softdevice112 on nrf52805.
I have setup everything and I can see bootloader and app working, just a question about memory layout...