Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi. I'm going to decode JWT (ECDSA sign) but I'm stuck. There is simple example to sign payload, but how can I decode JWT which I get from another device via bluetooth? I...
Hi I'm trying to debug the record_text example in the nrf connect sdk. However when I attached my nrf5340 dk and hit debug in the nrf connect extension, the process stops...
Hello!
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am using two nRF52840...
Hi,
I have ordered custom board based on nRF52840 SoC couple of times from JLCPCB and that included assembling as well. Unfortunately, 90% of the boards had floating aQFN...
Hi,
I'm using the Bluetooth sample called Central HIDS and want to develop a feature that stops BT scanning after a few minutes.
However, during development, I encountered...
Hello,
I have a question regarding the consumption of the nRF9161 DK board when it is under the following conditions: MCU on IDLE, modem off, wake on GPIOTE input (event...
Hello, I am wondering - Is it possible to program BL651 Bluetooth 5 with nRF52810 using pca10040 development board with nRF52832 on it and using
BLE HID Keyboard and Mouse...
Hi,
I recently started upgrading an nRF chip on old SDK to the latest nRF Connect. The device has only one button and currently uses a static passkey (written on the device...
Hi! Firstly I am somewhat new to developing on nordic chips so I'd like to apologise in advance or any silly mistakes or oversights I may have made. I am currently working...
I am using NCS 2.6.1 and have programmed a nrf52840dongle (USB Dongle) with the build result of nrf/samples/openthread/coprocessor
The problem I am having is that normally...
Hello,
I was able to setup nRF5340 Audio DKs as gateway and headset, test the USB audio input and enable the Walkie Talkie demo. But in both cases I'm using I2S/analog headset...
I want to use the signing script as mentioned Technical Documentation (nordicsemi.com) , however, with NCS, this script is not automatically being picked up during the build...
EDIT: I thought I had enabled RTT terminal output in this proejct, which I had not. Obviously this will have an impact on my problems sorrounding RTT terminal output. So I...
Dear all,
I used till now an application to route BLE data over serial port through the dongle USB nrf52840, SEGGER IDE and 1.9.2 nrf conneck. All works well.
Now I'm...
