Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I have discovered a serious issue with Bluetooth connectivity on iOS 26.
My device use nrf52832 and sdk15.3, it consistently disconnects just a few seconds after a successful...
Hello, i am already 1 week trying to make tracing working. I have NRF54L15DK and SEGGER J_TRACE PRO. I solder trace port on the board.
I did enable => nRF TPIU in nRF KConfig...
I've tried to compile "hello_dect" example using v2.6.1 toolchain and v2.7.0-rc-2 SDK. The sample code is present so I assume the SDK is correct version. However it fails...
Hey folks, I'm trying to use SPI00 instead of SPI20 to achieve higher frequencies and driver fails to initialize no matter what I've tried to do on NRF54L15-DK. Here are relevant...
Hello,
I have 9 sensors based on NRF54L15 working as GATT server. I push around 100 bytes every 15ms from all sensors to the central hub. When i connect all nine of them...
Hi everyone!
I am developing device based on nrf25833 mcu which should transmit data to android devices using ble characteristic notification mechanism (data received...
Hi!
Recently I bought this device (v1.1.2) and I was very happy about it until I tried to verify the current and voltage readings. Tried two multimeters and they both agree...
I am porting and existing app to nRF Connect SDK 2.7.0 from 2.6.1. Using sysbuild, MCUBoot and the app are building and I am able to load the firmware onto the PCB and it...
Hello!
I've just come into contact with the nrf54l15. On the customer's board, it is necessary to change the NFC pin to a regular gpio, and they following the previous nrf52...
Hi Is it possible to configure project to use simultaneous multi image DFU and serial recovery over USB? I would like to be able to update both cores using dfu_multi_image_XXX...
I have an LED connected, and I want to use PWM, but enabling it adds about 700 µA of passive current — both when the output is high and low. However, if I set the duty cycle...
Hi,
I'm developing on the nrf5340 and the semtech LR1110. I'm using the latest SDK version 3.1.1.
I saw in the SDK that there's a library for the LR1110, but I can't activate...
Hi.
I try to build the example Matter: light bulb and in the terminal shows an error that iI don´t underestand what is the problem.
Please ¿Any could explain me why ocurs...
Hi,
I am using the Thingy:91X device and can see the updates appearing on the hello.nrfcloud.com web application, but I would like to have access to the 'device' via the...
