Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi,
I'm using SDK17.02 on nRF52810, when my application have an error, it will log "fatal error" but never reset system. BTW, I'm not debugging and just watching the RTT...
I 'm developing a program (C# ) on PC for the nRF52840 dongle (pca10059) that is a RSSI scanner.
Scanning different BLE channels in the environment. The program is much...
Hi Sir,
We plan to test the WebUSB example under the below path:
/ncs/1.8.0/zephyr/samples/subsys/usb/webusb HW: nRF52840-DK When we compile, program and connect to the...
I bumped into some compilation errors regarding PRS box4, when I tried to remove UART from an example.
I saw that PRS is "Peripheral Resource Sharing", but it looks like...
I am working on nRF Connect SDK 3,9.3 version. One day a dailog to update appeared. I clicked to update while SES was also opened and I was working on a project. Suddenly...
Hi,
I am working on a firmware and have added custom services to HRS example on SDK 17. I want to know if its possible to add BLE multiperipheral capability to my device...
I don't have enough pins to dedicate a SPI bus to the nRF21540.
In the webinar I attended I believe I heard that the SPI bus is not supported by the current SDK anyway,...
Hello everyone,
This was discussed before, elsewhere ( link) , however, it is meant for the "nRF51422 chip " and I need to resolve some other points too ...
it is necessary...
Hi,
I am working on the sample DFU OTA project as recommended below,
https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs-dfu?CommentId=3cb5df69...
I am developing an applicaiton to run on the app core of an nRF5340, and I have mcuboot enabled for the purposes of handling DFU.
I have recently implemented signing the...
Hello, I am having a problem with the development on a custon board. During system-off I wake up the chip with nrf_gpio_cfg_sense_input function on PIN 5. The chip wakes up...
Hi
I am designing a new BLE device and have some questions about the PCB antenna.
The product will be worn on the body.
I have a 4 Layer PCB with 1.0mm with and 35u...
Im trying to use the BLE LTE Gateway running on a NRF9160DK
I have the NRF52840 running the lpuart_hci code and that is working fine i can configure the BLE from the NRF9160...
I have nRF9160DK kit. The iBASIS SIM does not work in India. I aaranged a M2M SIM from Voadfone. The Vodafone SIM has 20 digit ICCID printed on it, while the nrfcloud accepts...
