Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
I am a bit confused by the name and example use cases of 'NUS'.
The name is 'Nordic UART service' and it is often described as "A Serial UART interface over BLE" that is...
Hello.
I'm trying out nRF Connect SDK v3.1.0 with nRF54L15-DK.
docs.nordicsemi.com/.../release-notes-3.1.0.html The release notes say:
Updated by increasing the default...
I'm using the board RAK19007 with its RAK4630 nrf52840, meant for solar and battery, where the AIN3 (P0.05) comes from a voltage divider of VBAT, where AIN3 = VBAT*(1.5M/2...
Hi,
Board: nRF9160-DK (PCA10090 - v1.0.0) SDK Version: nRF Connect SDK 3.1.0
Goal
We’re trying to configure the nRF9160 to use external storage as the secondary partition...
Hi,
Please note that I am using below setup
NRF SDK17.0.2
Softdevice 7.2.0
For one of my application, I am trying to generate combined hex file with DFU, Softdevice...
my devicetree code
among which
Wave line error， I copied it based on the official Nordic tutorial SPI
I hope you can tell me in detail why the error occurred
Hi,
I am having issues testing the nRF5340 Audio DK, I have two dev kits and I am trying to program one with the Unicast Server and one with the Unicast Client hex files...
I’m working with a custom board based on the nRF52833. It uses an external 32 kHz TCXO (SiT1552) as the LFCLK source.
In my main Zephyr app I set: CONFIG_CLOCK_CONTROL_NRF_K32SRC_EXT_FULL_SWING...
I was developing with the nRF54L15DK, creating a Radio driver to do Proprietary 2.4GHz communication. In the driver, I use nrfx_event_to_bitpos() and nrfx_bitpos_to_event...
When trying to receive an LE Audio broadcast, issuing an HCI_LE_BIG_Create_Sync command with parameters obtained after scanning for ISO broadcasts, the
HCI_LE_BIG_Sync_Established...
Hi Team,
We have started our cellular development using nRF9160 modem using SDK 3.1.0.
We have selected this MCU because it support all security features, we are going...
With SDK 3.0.2 and 3.1.0 we noticed that during a build, even a 10-core i7 becomes almost unusable. The reason seems to be that all cc1.exe compiler processes run at normal...
Hi,
Is it possible to make the MQTT connected device receive the Shadow config updates and AT Commands immediately? Based from our testing, the device only receives the...
