Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
When I tried the official sample: nrf 70-wifi-ble-image-transfer-demo, and tried to apply the shutdown operation to it, I found that there would be many problems with the...
Hi,
I would like to create a project for a BLE peripheral for nrf5340 based on a standard sample like "peripheral LBS" und nrfConnect SDK v3.0.2 with modifications both...
I'm working in Windows using nRF Connect for VSCode and I'm trying to read registers from an ADXL345 over SPI. I have no issues reading the device ID in reg 0x00 but when...
I am developing a firmware for nRF52810.
Does Zephyr support debounce care for push button switches in ncs v2.6.1?
It seems that CAF supports it, but I don't plan to...
Hello. I'm trying to connect to a CoAP server (Thingsboard) with a certificate based DTLS socket. In Wireshark I see that the handshake failes, but not why. I post the relevant...
I have an application where I need multiple AWS_IOT_SEC_TAG to connect to different AWS IoT servers, including the nRF Cloud server. How can I do that with the CONFIG_AWS_IOT_SEC_TAG...
Hi all
Im trying to implement on bluetooth communication between two nrf52840 DK, I have made a custom uuid service on peripherial. Now I have to do GATT discovery service...
Hello! We are developing a schematic for our device and trying to correctly assign GPIOs for different peripherals. There is the Cross power-domain use section in the documentation...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hello at all, I try to compile the example peripheral_uart for the nrf54L15-DK. The goal is to compile without west. My directory structure:
where I copied everything from...
Hello,
I am developing on the NRF54L15 DK board, using the SDK v3.1.0 and v3.1.0 toolchain. I am trying to use the macro NRF_RADIO_INT_RSSIEND_MASK, but RADIO_INTENSET_RSSIEND_Msk...
I'm using the NRF5340. When I open a standard example project located in the directory: nrf\samples\bluetooth\peripheral_uart (the well-known Bluetooth data transparent transmission...
I am experiencing system resets caused by the WDT (Watchdog Timer) while using the nrf52832。
This is my WDT configuration code：
void system_wdt_init(void) { uint32_t err_code...
my sdkconfig.h related to fds
my entire code error: my entire sdkconfig
i have tried changing no of pages , using nvmc driver, but i am getting the same error steps...
