Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi,
I'm using the nRF5340 DK and SES 5.34a, nRF Connect SDK v1.4.2. For python, I use pyenv virtual environment for which python is set to 3.9.1.
I am able to build and...
Hello I have a question. After when I have used saadc, the consumption increases by 0.9mA. And stays it so. Do you have any idea, how to find out what it does?
saadc init...
Hello,
I'm using a nRF52832 chip and attempting to broadcast a public MAC address through the application. I'm observing that the device broadcasts MAC Address FF:FF:FF...
Hi.
I am building my application on top of ble_app_uart__saadc_timer_driven__scan_mode example.
I want to interface an i2c device with it. The i2c device works perfectly...
Aim:- To read temperature and humidity over a mesh network and display it in an android application
Devices to be connected in Mesh :-
nRfF52840 Development Kit x2 ...
Hello,
I am currently working with nrf 52840, using segger embedded studio (V5.34) and SDK 17.0.2.
For some reason, when I open any example under ble_peripheral, such...
Hi,
I installed nRF Connect SDK v1.4.2 by the tool chain manager and was following the Getting Start guide and entered here.
https://developer.nordicsemi.com/nRF_Connect_SDK...
Hi,
I have two variants of the nrf9160 SIP one being the nRF9160 SICA B 0 A and the other being the nRF9160 SICA B 1 A.
When I use the AT%HWVERSION AT command on the B0...
Hi,
I want to write my own Multilink/UART example from scratch, because I'm too confused from all these examples.
What I need to get that code done? Or has anyone build...
I am trying to download the softdevice to the nRF52840 development kit using the nRFgo but:
1. On nFRgo I didn’t found the “Program softDevice tab”
2. Although the kit...
Hi
Migrating from NCS1.3.1 to NCS1.4.1, the Blinky sample stops working on my custom nrf5340 board. No compile error, but not running. I also have a nRF5340PDK. Works fine...
I want to use long range ble for advertising with nrf52833. I have a PCA10100 SDK board, and I'm running a program with type of BLE_GAP_ADV_TYPE_EXTENDED_NONCONNECTABLE_SCANNABLE_UNDIRECTED...
Hi!
So I've got one BLE Central and one BLE Peripheral that I should communicate. Ive based the Central code on nrf Connect SDK's "peripheral_gatt_dm" sample. First I...
Is there an existing implementation on how to do diversity (BLE) with dual antennas using nrf21450?
(could also be by using other antenna diversity switches / brands)
