Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Greetings!
I am using NCS 1.4.99. I have spent some time debugging my I2c application on NRF5340 and I came to the realisation that I was not able to control any pin that...
Hi,
I'm developing a program using SPIM instance 1 on nRF5340 PDK, with nRF Connect SDK 1.4.0.
The problem I met is exactly the same as this post . If I want to use a...
NRF52832, nRF52840 is under consideration for development. Because of the implementation of Secure Boot and Secure Key Storage capabilities, we want to choose the nRF52840...
Hi,
I was able to upload a binary file before, but not able to upload a binary file to nRF connect app in order to FOTA.
Could you please help me to upload a binary file...
I am trying to compile and run the ble_app_hrs example for an nRF52810 dev board, using Segger Embedded Studio v5.34. I am using nRF5_SDK_17.0.2_d674dde, with s132. This is...
Hi,
I am looking for a working example for upgrading the MCUBoot itself when we have the configuration B0+MCUBoot+APP, especially wrt to SLM application.
I have gone through...
Hi, I am developing using Segger Embedded Studio.
I downloaded the module and checked that output/debug/Exe has a .hex file.
Then can I download this output file back...
Hello,
We are testing Angle of Arrival feature which was released in Bluetooth v5.1 We are currently using Texas Instrument CC2640R2F and TI angle of arrival board to...
Hi,
I'm using nrf52840 with BLE functionality.
I don't use sd_ble_gap_tx_power_set in my application.
Does it mean that I'm using default power (dbm)?
What is the...
Hi,
i am trying to interface an external spi flash memory with nrf52832 to store temp. data.
i tried to read the manufacture/device id but i am getting wrong data.
my...
Dear Sirs
We are planning to have our end product certified by FCC and CE. It uses the nrF52840 SOC directly on our PCB. This has the following QDID : 124988.
We have...
I am using cjmcu 8223 board for my project so for uploading program I brought a ST-link V2 pen drive like device but I can't able to detect the board on the ST-link software...
Hi
I am currently evaluating a 52840-DK (from 2017 I believe) and several 52840 dongles (ordered very recently). I managed to successfully run the light/switch mesh example...
