Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
There are only the last version nRF51822 Product Specification V3.1 on the web. However, I need a V2.0 PS. So, where can I download the nRF51822 PS V2.0?
Hi,
I wrote a very simple program which compare the analog reference input 0 (P0.00) with AIN0 (P0.26) and generate an interrupt on cross using Low Power comparator on...
Could you update the ble-app-lbs example for SDK 7.1.0?
github.com/.../nrf51-ble-app-lbs
I haven’t been able to get it work.
Since the led_char_add() uses these setters...
Is there a limit to the number of characteristics per (custom) service?
After some testing, it looks like 20 is the maximum (21 causes the device to stop functioning) ...
Hi All,
I am an electronics engineer but new to nRF51822 programming. I have used the PCA10000 & PCA10001 using Nordic SDK, using nRF Studio etc. In nRF Studio, you can...
I'm using SD110, and in my application I have an array of 64, 32-bit integers.
Typically, the client will only need to read 1 of the 64 values, or write to one of the 64...
I'm just getting started with the nRF51-DK, and I'm still confused about which SD I need to load, and which roles I need to support aka GAP and GATT.
My end application...
Hi,
It seems to me that pin assignment and package is the same for both nRF chips. Can I solder nRF51422 chip instead of nRF51822 for ANT testing purposes on my PCA10004...
Hello,
I have a custom board (was built using the Nordic schematics provided with the Smart Beacon Kit). I am using J-Link LITE to try and program the board.
The board...
Today nRF Toolbox App on my Android 5.0 phone is only recognizing HRM code running on my nRF5182-mkit, not other examples.
Today nRFToobox and nRFUART2.0 Apps both...
Hi,
I hope use nrfjprog.exe to do following things:
HW: nrf1822
download s110 6.0
download bootloader
download firmware
write some values to certain addresses...
Hi,
I've tried to search the documents and the forum for an answer to my question, but didn't have much luck.
We have a custom board that uses a STM32 micro and nRF51822...
Hello,
I am currently trying to find out how the BLE devices keep their connections in sync. According to the spec, the peripheral can have a slaveLatency of up to 32s...
Is it possible to run Master Control Panel and the PCA10001(or the J-Link lite) at the same time on the same PC, or will that cause problems? I guess I could simply try it...
