Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
hi I have recently been developing ncs on vs code. However, I encountered a strange problem. After I clicked build configuration, there was no output in the terminal, except...
Hello all,
I have this problem: when I add support for OTA my bonding information are canceled after power on. Without ota all is perfect.
Example: - Turn on the device;...
Hey there!
I am currently trying to upload a .hex file onto the board to flash it using the nRF connect programmer. But while flashing i get this error:
11:10:10.496...
Hello,
I am currently working on the Exercise 3 – Interfacing with ADC using nrfx drivers and TIMER/PPI sample. I have it operating, however I am wondering what is the proper...
Using NCS 2.6.2
set(PM_STATIC_YML_FILE ${CMAKE_CURRENT_SOURCE_DIR}/configuration/pm_static.yml) in the CMakeLists.txt works well to use static partitions for a appl+mcuboot...
Hi
I have been using the nrf52840 development kit. In the sdk examples I am running the radio test example of pca10056, but in the retarget.c file I am getting this error...
Hi,
I'm working on a testbench to flash product with nRF5340 and nRF52840 chips.
In order to erase/flash both I'm using JLink Base compact and nrfutils CLI. But I have...
I've been trying to build the BLE Audio Broadcast source to run on my nRF5340 Audio DKs using the line in as the audio source. I've been developing on nRF52 for a while using...
Hi!
I need to create an application that sends text messages to a private server, such as ptsv3.com.
Could somebody please help me make this application work?
I encountered...
Dear Community,
I am currently working on an LTE-M and NB-IoT project in India using the nRF9151DK and testing the AWS IoT sample. Everything is set up, except for an active...
Hi, We are using following HW and peripherals: - nRF52840 - I2C - ADC - RTC1 - RTC2 - PWM - GPIO - SWI. We are using following 3rd party libraries: - nRF5 SDK v17.1.0 - FreeRTOS...
Hey All, I am sorry if this question may seem absurd or very very illogical, I am not very good at hardware but here I go. So I am designing a circuit around nRF54L15 as my...
Hi for the nRF54H20 the ds says there are two options for how to supply VDDH: either VDDH=2~5.5V with config 1 or VDDH=1.8V with config 2. If my system has 3.8V from a lithium...
