I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Looking for someone that has previous experience building multi protocol / time slot topologies using a mix of BLE (central+peripheral) & custom Gazell connections running...
Hi! We're considering switching between the mentioned packages, both in nRF52833.
I've looked around dev zone and product specificaiton pages, and could not find anything...
Our device connects to a cell tower and then creates a socket to our gateway. I monitor +CEREG to see what it goes through to connect to a cell tower. Below is the meaning...
I testing UART0 data transmossion. But, could resolve why CPU resets when executing : if (!nrfx_is_in_ram(buf)) in uart_nrfx_uarte.c file. See atached image, where Reset occurs...
I am developing a custom board with an electronic paper device (EPD) attached, which will be controlled with SPI and a five additional GPIOs (a mixture of inputs and outputs...
Hi Guys,
I have a nRF5340-DK(PCA10095) here and I'm planned to perform some BT-SIG RF testing with it but I can't find the proper hex file for DTM(Direct test mode) setup...
I (think I) have successfully located the code responsible for handling the data received BUT! The code segment:
in app_uart_fifo.c
seem to only receive a paltry 1...
Hello
I want to measure Low power current in nrf52840-DK with System ON mode.
I need to know how much current consumes by nrf52840 SoC while I2C Engine ON, SPI ON, and...
Hi.
I am working with the nrfConnect SDK 1.8.0. I would like to configure the nrf5340 for maximum throughput to work as a server for a smartphone device.
How should...
Hi all,
I am using NRF52840 and I am saving some data to the flash memory using fds. The data are 216 bytes in each file and there are 3400 files which is in total 734kbytes...
Hi,
In my application, I am writing in flash.
But when I do so, my openthread data in flash gets o verwritten, the node doesn't retain its commissioning data.
In nrf_SDK_For_Thread_and_Zigbee...
Hi All ,
I am using nrf9160Dk ,When i use asset tracker V2 i successfully get the GPS values on the nrf Cloud . But when i use the Asset Tracker only then i am unable to...
Hi there,
From the product specification of the nrf5340, we can only find UARTE peripherals (UART with EasyDMA). Is it possible to implement uart without DMA? Of course...
Hi
I was just curious as to whether or not there is a specific reason the Xenon's PWM capabilities are not available with NCS/Zephyr. Is there a hard limitation or is this...
Hi Team,
SDK - 17.1.0
chip -nrf52810
I want to store sensor data (12 bytes) every 30 seconds in flash memory. Once the flash is full, I want to replace the old data...
