Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hello. I am downloading a custom board (nrf52810) using the nrf52832-dk board as shown below.
I compressed and managed the project file after taking over for company business...
Dear Team,
We are developing a product based on ble mesh. We are planning to select NRF52840 as master device and nrf52832 as slave device. Slave devices should be more...
In the ble_app_beacon example in nRF SDK 17.02, there are two defines namely APP_BEACON_INFO_LENGTH (0x17) and APP_ADV_DATA_LENGTH (0x15). The former defines length of the...
I am trying to port some code from the nrf52840dk (PCA10056) to the dongle (PCA10059) and everything seems to work fine until an interrupt is triggered. All serial output...
Hey! I have a project with custom board with nRF52833 and I would need help with just getting data from sensor via i2c and sending it via bluetooth to mobile device. For some...
Hey!
I would like to use the nrfjprog executable from the nrf command line tools for flashing the nrf9160 modem firmware. I read some older tickets about this issue and...
I have a requirement to start the MCU with extended non connectable advertisement for few minutes and then activate normal connectable advertisement for another few minutes...
Hello,
We have an app_timer that runs periodically for the application, and we are also using BLE peripheral code. Once the application timer expires, the event handler...
Hi,
The Dongle was given to me by a colleague of mine who has the exact same laptop as I do. The Dongle was and is working fine with his laptop. The problem is with my office...
Hi ,
i am using nrf52832 soc with customize board trying to optimize the power the following events occur:
1)The first time when i code uploaded it initialize all the...
Hi,
Is there a way to set somewhere in the softdevice or a library to automatically disconnect after an idle connection? Idle means, nog characteristics being read or written...
Dear Nordic,
I have some questions when study the usb audio of nRF52840;
What function when running the nrf_drv_usbd_errata_104 function?
Do I have run it? Can I remove...
Hi,
I am struggling to find a basic sample for UART communication in NCS. As an experienced Nrf5 SDK programmer, I find it very hard to convert my firmware to nRF Connect...
Hi Nordic Support
I have been experimenting with your nRF52840 board there has an SPI flash and have tested it with your USB example that can enumerate the filesystem on...
Hello,
I have the following setup:
a computer connected to a PCA10040 over USB
a PCA10040 connected to a NRF52832 over SWO (SWD IO, SWD CLK, SWO, RESET).
I would...
