I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I am using Keil v5 and the nRF5 SDK 17.1.0 .
I use this example.(nRF5_SDK_17.1.0_ddde560\examples\ble_peripheral\ble_app_uart\pca10040)
I hope the chip enter system off...
Hello,
We are using the nRF52840_CKAA_R7 package of the nRF52840 on our custom board. The board's USB pin connections are designed based on the nRF9160-DK's nRF52840 reference...
Hi,
I just received my Thingy91x. I followed the onboarding and created a provisioning profile in NRF Cloud. The device did not connect and no logs appeared in Serial terminal...
Hello everyone,
I am trying to execute Nordic Bluetooth ESL tutorial with PAwR. Here, I am able to change the images and handling the state of an LED connected at the Tag...
Hi,
We are encountering an issue where the existing firmware does not run on the chip when powered by a coin cell, even though a 3.3V power supply is available from the...
When I compiled and flashed the Nordic Distance Toolbox example onto two nrf5430dk boards without changing any options, the following message appeared on one of the UART ports...
Hi,
I have the following scenario:
nrf5340
SDK 2.1.1
HFCLK: 32Mhz crystal
LFCLK: square wave of 32768 Hz from an external RTC, range [0 - 1.8] Volts
square wave...
Hi, I am using a custom nrf52832 device. In that device , button is connected with reset pin P0.21. due to reset functionality I am not able get interrupt from button.
how...
Hi,
I am using nrf52840 to develop a product. I use NCS sdk v2.5.0.
I developed a project based on the [Bluetooth: Central HIDS] example in the NCS SDK. This example enables...
Hi,
i am using SDK 2.1.1 with nrf5340.
I would like to add the linker option --wrap.
What are the possibilities to add this option in Visual Studio Code ?
Could it...
Hi,
I am using nrf connect SDK 2.9.0 with nrf52840DK and MCUboot with own RSA .pem file (from older versions, so no ECDSA possible). How can I increase verbosity when building...
Hello,
My BLE peripheral code works fine with Android devices, but it is failing with iOS devices. I am encountering an error message: "Ignoring data for unknown channel...
I'm working through the tutorial here. https://academy.nordicsemi.com/courses/nrf-connect-sdk-fundamentals/lessons/lesson-4-serial-communication-uart/topic/uart-driver/#uart_config...
I'm working with nRF52840, my function will read wav file from SD card and play it using Zephyr I2S driver. My source code about playing sound in below.
The strange is the...
Hi,
For a meter application with battery, I want MCU is sleeping but comparator still working to count a pulse input (freq <100khz)
Can Nordic IC can support this idea...
