Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Looking for someone that has previous experience building multi protocol / time slot topologies using a mix of BLE (central+peripheral) & custom Gazell connections running...
Hi.
I have nRF51422 borad and want to flash to nRF51422 with JLink.
I supplied to 3.3V power to board and is connedted SWDIO to p23, SWDCLK to p24. JLink is connected...
IUsing the Master Control Panel application on my Android device to connect to my nRF51822 module (acting as the GATT server), I have implemented the Device Manager (v10 SDK...
I have successfully compiled BLE application using tutorials provided on nordic website.
but when I start doing debugging for better understanding find out that I can not...
Hey,
We got a problem when trying to figure out how to detect the custom services from Unity. We are trying to read data and afterwards to do some manipulations of objects...
We are using the Nordic fork of Zephyr on nRF5340.
Looking at the serial interface peripherals (SPI/I2C/UART), we understand that these have shared resources and only one...
When uploading programs to the nRF24 chip, is there a "single memory space" or is there a "bootloader-only memory space" and a seperate program memory space? or is it all...
Hi All
I am using S130, nRF51822, SDK12, My RTC1 compare events is connected by PPI to ADC, I have set it to generate an adc_ppi_event_handler after 6 consecutive compare...
Hello Team,
First Thanks to all Nordic support:)
My problem :
I have interfaced SGTL5000 with Nrf52832 (used SDK 16) I'm getting the audio data on aux connector and...
Hello!
I have problems with bt_shell sample from sdk-zephyr , when I use SoftDevice bluetooth stack( nrfxlib ).
When I switch on CONFIG_BT_EXT_ADV option in menuconfig...
I got an example that uses PO.13 for analogue input. It does this by referencing it as ADC_0. That seemed to work OK when I hooked up to PO.13 on the nrf9160-DK
Then I changed...
Hi, We are currently attempting to turn off unused parts of our RAM, and the app's linker space is configured to NOT use the turned on RAM. The problem is that the bootloader...
Good afternoon! I would like examples of projects on Soft device S140 long range to test the work of BLE Long Range HCI-USB host - need to be able to connect to them. (scannable...
I'm trying to achieve as close as possible to 48KHz (or 24KHz) LRCLK rate, in 24-bit mode (MCK/LRCLK = 48), on an nRF52832. With the values defined in `nrf_i2s_mck_t ` the...
I want to use libuarte. Target is nRF52832 and SDK17.0.0.2. Do I need to take workaround against Errata109 when using libuarte?
And, I done backport libuarte to SDK15.3...
I have been using nRF Connect SDK v1.2.0 to program my nordic thingy 91, however recently whenever i open IDE, Segger Embedded Studio gives the following error,
"Unrecoverable...
I am new to BLE and I have some question regarding Mesh and LPN which we cannot get a consistent result :
Assuming in a Mesh set up there are 2 Relay units (simply refer...
Hey,
I have an OLED trying to use, that is built in with a pcb design.
I don't know the manufacture to contact,
On my PCB datasheet says: the OLED Module QT-2028TSWIG02...
I created a TWI software module which runs well as standalone. Now I need to put together with BLE code to comunicate with Android APP. I'm stucked because when I initiate...
I am able to provision and configure 1 mesh device with the nrfMesh iOS app. I am able to successfully provision a second device, but when I configure a second device, the...
