I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi to everyone!
I have a problem when I try to connect to the Blinky application running on my nRF52dk.
My mobile phone (Nexus 5X, Android 7.1.2) is able to detect the...
Hello,
I am learning the different peripherals using the nRF52 DK (PCA10040). I am using the nRF5_SDK_16.0.0. I am using Segger Embedded Studio on Windows 10 64-bit machine...
Hi,
I am trying to use enhanced shockburst (ESB) to stream data at high bitrate between two nRF52 development boards. Even though I set the protocol to 2Mbs, the max netto...
I am testing a nRF9160DK board. I am located in Italy, so LTE-M SIMs would not work.
I have received some NB-IOT SIMs from TIM/Olivetti; I found a compiled sample "at_client...
Hi
I building a mesh network of sensors that will be spread across a building.
One node will have a cellular modem and will send the data to the cloud ( gateway ).
Data...
Hi, I got maybe strange and difficult question about nRF24E1 - I know that max supply is 3.6V, but I try to rebuild one project to Li-ION and I would like to ask if that chip...
There are many one star reviews for nRF Toolbox on the Android Play Store (not from me!). These one star reviews are from users complaining that the application does not find...
Dear All,
I want to program a device to perform the following actions:
Start->configure modem to connect to NB IOT, adjust the PSM and EDRX->potentially send a message...
Howdy,
Part of our design process for trying to achieve the most time out of the product's battery is optimizing any pull-up and pull-down values such that when active...
Hello,
After adding pairing using static passkey to my nRF52840 board, i am facing a memory issue :
At the beginning of execution, the code stopped as if there was a breakpoint...
Hi
I have a short question:
I am currently writing on my master thesis about an self built Asset Tracking System. There should be a micro controller as a receiver...
Hello,
I am using Segger Embedded Studio to run AWS FreeRTOS bootloader demo on the nRF52840. When I try to build, I get the error cc310_bl_backend_ecc.h: No such file or...
the first (initialized) Eddystone (e)TLM frame have vbatt unset. I am using SDK 15.3. I suggest the following changes, it simply busy wait until ADC reading is finished before...
I had been programming custom boards with the nRF52840 DK both through nRF Connect and the Command Line tool without issues. I have shorted SB47 to provide power to the target...
