Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Dear all,
I just played around with the nRF Sniffer and I am pretty impressed. Really good tool and most of the packets are received.
I want to build an application where...
I have reprogrammed the nRF52840 board controller. When I run the lte_ble_gateway application I get the following on the 2nd dev kit VCP port:
SPM: NS image at 0xc000...
hello, i have a question, i use sdk15.3 for nRF52832, i run for example flash_fds, sometimes it will not be able to erase or write to memory, after restarting the device,...
I'm having a problem that I get some presumable interference between a high flash memory activity and UART communication. I'm writing single words into flash quite often,...
I am working on a mesh network and i want to add a nordic thingy 52 to read temperature & humidity data over the mesh, let say to an nrf52 DK connected to a Raspberry Pi,...
I'm developing a Zigbee coordinator that works as an On-Off Switch for the Zigbee Profile HA: this connects to the Device Mains Power Outlet, again with the HA profile.
...
Hello to all,
I have a question about parsing zigbee commands when they present a payload.
I have a Coordinator that implements the Window Controller Device of the HA profile...
Hi folks,
Im trying to run the heart rate collector from a Visual Studio application and I have some communication issues with the connectivity device. I use a nRF52 Dongle...
I'm currently looking a bit into the bearer-layer internals of the nRF SDK for Mesh and noticed that there is a heap of instances where data needs to be transferred between...
Hi,
I am using nRF52840 and BLE coexistence (mesh and ble). I am able to connect to my board via BLE using nRFConnect for PC and a nRF52840-DK and change characteristics...
I'm trying to use DFU for the first time
I'm working my way through these instructions:
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting-started...
The SDK v16 package has a board file for the nRF52833 board, PCA10100, however this seems to reference GPIO pins which are not present on the device:
What should these values...
We use the nrf52832 in twi-master mode. The connected slave sometimes needs longer to respond than the default configured TWI timeout.
The timeout is defined inside the...
Is it possible to generate a zip package containing both firmware and softdevice in such way that the soft device will be updated only if the current device softdevice version...
I have some module chip connected to the nRF9160 DK providing the sensor data over I2C line. In some state transition of the module the short reset pulse needs to be generated...
