Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
Hi,
I'm testing an interactive pyaci example in Mesh SDK v2.2.0 with two nRF52DK boards.
Interactive mesh provisioning and configuration example worked fine so I modified...
I'm using nRF52+SDK11.0.0+S132 . It currently has SPI, SPIS, TWIM, RTC. I want to remove SPI and I'm getting: ..\components\drivers_nrf\spi_master\nrf_drv_spi.c(56): error...
Hello,
I'm using the nRF52 DK with SDK 15 and SD132 6.1.0. I have a custom service running that requires periodic characteristic writes. Occasionally when writing to this...
hi guys!
i'm trining to develop the nrf 52840 devkit in particular for the ble use.
from the documentation i didn't find anythingh about send a message to the dongle from...
Hello guys,
I am using nrf52832(PCA 10040) and transmitting radio packets. I want to collect the packets using raspberry pi. Is it possible?. If yes, how are the ways we...
Hi, everyone. I've been trying to migrate from the SDK 14.2 to 15.2, but I've been having trouble getting one new function to work. I previously used ble_advdata_set() to...
Hello,
I've checked a few related threads, but without any success.
I need to react on "Data Ready Interrupt" and read data from SPI. SPI and Device is initialized before...
I'm am trying to select an LDO to provide the VDD_GPIO power rail for the nRF9160 and am interested in selecting either a 100mA or 200mA LDO. Can Nordic provide a rough order...
Hi,
I was trying to communicate with an I2C device, which's address is 0x7C
But I always got NRF_DRV_TWI_EVT_ADDRESS_NACK event, so I took a check on the TWI wave:
...
Hi Nordic Team,
Meanwhile we are working with Laird BL654 which uses the nRf52840.
My questions:
1. Can we flash gazell examples on Laird BL654 with Segger?
2. If...
i'm trying to get distances between nrf52840 ble transmitter and receiver, using measured rssi upon receiving ble_gap_evt_adv_report_t from ble stack. in order to calculate...
In file sdk_config.h, in order to configure a calibration interval of 8 seconds, what number should be used in the define NRF_SDH_CLOCK_LF_RC_CTIV?
The time units are not...
Good day,
I again have an interesting question). There is a useful descriptor to better understand the purpose of the characteristic. This is a 0x2904 handle (GATT Characteristic...
