I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi,
I am using SDK 12.2.0 with my custom board. As per the my requirement, i need to ground or set logic 0 of my gpio pin no. 12.
So, how can i do this?
good morning to all
I wanted to ask if anyone has a design of nrf51822 where an external temperature sensor is used, to know how the connection to the chip is. Should I buy...
Hello,
I am learning about the behavior of "Notify" transmition.
From some web sites including below, I understood as follows.
devzone.nordicsemi.com/.../
So could...
Hi,
I am new to arm and ble development. I am used to work with AVR mcus and I am trying to migrate a project from AVR to nrf52.
AVR usually has some "General Purpose...
I'm transmitting data packets each of 48 bytes in the form of notifications using Bluetooth 5.0. When I observed the logs over sniffer, I see that the packets are fragmented...
Hi,
iam new to all this and hardly find answers for my question:
Is it possible to pair a nRF51422 with an Ant+ remote especially Bontrager TransmitR and use those remote...
nRF52832
Hi,
I am a little confused as to what component uses ble_flash (...drivers_nrf\ble_flash\ble_flash.h/c) and why? What is the difference between this and SD...
Hello all,
I've ported the buttonless DFU example to my project without the buttons or the LEDs, but I only tested the bootloader and not the uploading capabilities with...
I want to know the details of "DTM testing using nRFgo Studio".
On page 52 of "User Guide v1.4 of nRF51822 Development Kit" says, "For details on how to use the Direct Test...
Hi.
I bought the nrf51822 kit, and I have questions to ask.
I know that there are many sample code provided by nordic.
I know that the sample code will run...
Hi!
I am working with an application were two nRF52832 shall communicate over UART in half-duplex 1-wire mode (similar to what is described here but I use different pins...
Got one new Thingy52 and worked all nice with both Android and iOS teminals.
Then I have tried to upload new firmware using the iOS.
Loading new firmware progress was...
I just tried the Button example on the nrf52-dk development board, and the interrupt for the defined button GPIO does not seem to * trigger
Zephyr 1.8.0 ( fcb9144dc git...
I have been using nrf52dk as programmer for external modules (BMD-300) during development. I'm wondering if I can still use nrf52dk for production devices or I have to get...
Hi, stupid question here: Is there a command I could send via the dfu characteristics that starts the application somehow with doing an actual dfu update? Using the secure...
