I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
In my current design, for the schematic and layout I've copied the design of the first version of the usb-stick with meander-antenna and matching network/balun. In the later...
Hi,
I have been programming PCA10028 using these commands for a while without any problem:
$ JLinkExe -device nrf51822_xxaa -if swd -speed 4000
J-Link>loadbin s110_nrf51822_7...
hello,
I am using S130 softdevice in nRF51822 DK. I made one device as peripheral and other as central. My peripheral is acting as GATT client and central as GATT server...
Hi everybody,
I test the pstorage library. But it didn't work. I print the result with uart, as the image shows. But as you see, It has some problem. And I have no idea...
Hi sir
If nRF51822 unexpectedly enter DFU OTA mode, did boot loader have timeout counting to exit DFU?
Besides, if nRF51822 entered DFU mode and didn't update new firmware...
Hi all,
This 60-second limit is not enough for us. Our application is 48 kB & takes 35 seconds to upload. It should be enough, but the problem is that our iOs app does...
Hi All,
I use S120 device to monitor advertising and output the mac address,RSSI information via UART to PC terminal. The PC terminal can receive data continusly from the...
I found ble_dfu.py referenced in some posts to help automate the generation of an application.dat metadata file used (along with the application.hex file) to create the input...
in the code below, the keil IDE is flagging with red squiggly APP_BUTTON_INIT, claiming that it is an undefined symbol. It also says that this implicit declaration of 'APP_BUTTON_INIT...
Hello all.
while trying to calculate the data rate from bluetooth low energy , i have two questions
Is there a possibility to measure the data rate by using nrf sniffer...
I have an algorithm which does quite a bit of number crunching. I'd like to know how many clock or instruction cycles this algorithm is using. How can I get or calculate the...
Hi all,
I am not sure what to do now. I have been trying to get the s130 working with the device manager. I tried using github.com/.../nRF51-ble-app-hrs-s130 with sdks...
Hello,
in my application i use a bootloader for S310 and S310 V2.1.0.
The Bootloader is configured to use NRF_CLOCK_LFCLKSRC_RC_250_PPM_4000MS_CALIBRATION and the application...
Hello Everyone
I am using two application timers one of standard battery service and one i have made for adc sampling like this along with the code added for battery timers...
When I update the advertising data from the radio pre activation hook (800µs), the updated data does not appear in the advertising event following 800 µs after the hook is...
