Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
I'm trying to build my project for nRF54L15 DK. The project uses mcuboot. When mcuboot is being built, I get following warning:
I guess the problem is caused by the config...
Hi, DevZone,
Our customer, Hosiden Osaka, wants to get the recommened foot print regarding nRF54L15, that is, the following each land pattern respectively;
- WLCSP 300um...
I am writing a program for the nRF52805 for use in a battery-operated remote. It needs to wake up from sleep when any button is pressed, perform the interrupt (blinking an...
I have found that in NCS SDK 2.6.2 it was very simple to enable FLASH_SIMULATOR as part of the mcuboot configuration overlays. But starting from SDK 2.7.0, I keep getting...
Hello.
I found this in the sx126x .c driver :
These lines did not allow adding more than one device to the overlay . I removed this code and rewrote all driver files...
example Matter_light_switch in vs code
version using nrf connect sdk -> v2.8.0
manage tool-chain version v2.8.0
nrf52840dk
getting error while building code
...
Hi,
I follow the execise https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-8-bootloaders-and-dfu-fota/topic/device-firmware-update-dfu-essentials...
Hi,
I'm trying to find the BOM referenced in the Hardware Design Guidelines for the nRF9151 under the Schematic Design section. According to the document, the BOM should...
Is there a way to obtain the Tx/Rx packets num in LE Audio? I want to calculate the PER in LE Audio. Using nrf v2.60, NRF 5340 Audio DK.
Thanks for your reply.
When configuration options CONFIG_SEGGER_SYSTEMVIEW =y and CONFIG_TRACING =y are added to my prj.conf the following build errors are shown:
followed by many other errors...
Hi,
I have a NRF52840 DK , I was using it for development. After one day the board don't turn ON anymore. I'm using USB cable as a power source. Acording to several subject...
Hi:
I use ncs v2.8.0, using external flash(w25q128).
this is test flash project.
And this log:
Device_is_read returns a failure. But flash read/write successful...
I'm encountering an issue with the use of the GPIO interrupt type GPIO_INT_EDGE_BOTH on a GPIO connected to a button. When pressed, the button pulls the GPIO to GND, and when...
Hi there,
I am new to the platform , we are working on a proof of concept to reduce idle power consumption as low as possible on an NRF9160, I want to put the system in...
Hey,
We have a library (rust) responcible for communicating with the BLE peripheral Using btmgmt dbus messages to bluez.
We have never initiated a dedicated `aagent` in...
