Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi, I was using nRF52840 , flash is mx25L25645GM2, I used fatfs with QSPI ,but I found fatfs was unstable,After some time, the stored file would dispear.Sometime there were...
what is credit based flow control in L2CAP connection oriented channel..?
What is meaning of credits..?
what is exact usage in IPSP ..?
How it will effect data communication...
Hello,
I am preparing sniffing workspace for BT Mesh, where I have 3 devices in the Mesh network (provided by nRF Mesh app) and I need to read SRC, DST, SEQ and simmilar...
I tried to run my Thingy91 off the battery but it shuts off instantly.
My questions is if the battery charging functionality is in the firmware or hardware? Trying to figure...
Dear Nordic support member,
Where does "pca10100e folders" be installed?
I have nRF52833 development Kit. But I could not find pca10100e folder.
Note: My IDE is IAR...
Hi, I am looking to develop applications for the nRF5340. After watching the "Introduction to Zephyr RTOS" webinar, I saw that the software engineer presenting the demo was...
Hello
I am making a project in SDK v17. I want to use mpu6050 sensor but I don't know how to use library included in SDK.
The example Martinsbl has in GitHub is optimized...
Hi, i'm trying to find a way to use the Nordic nrf52840 with Adafruit SIM7000-LTE-Shield, the only apparently way is with Arduino IDE but i´m not using it (no success at the...
Various errors during medium-term deployment of cellular-enabled sensor device
We've prototyped an agricultural gas sensor based on the nRF9160, which takes readings every...
Hi,
We are having trouble getting the Thingy91 firmware running as is. We have achieved this in the past but I had made too many modifications and I decided to scrap it...
HI! I'm on Windows x86 and I've followed the steps from the getting started assistant. After trying to locate the board directory ncs/zephyr/boards/arm/nrf9160_pca10090 ,...
I am doing a custom desk for a client and I had this idea of adding a electromagnetic lock on a drawer. That is easy enough but I thought that maybe I could add a couple of...
Hello If I an exemple like ble_thread_dyn_mtd_coap_cli and that I configure the mode in MULTIPROTOCOL_802154_MODE_FAST_SWITCHING_TIMES: do you have any idea how long it takes...
I have two SPI buses on my board, with a different type of slave chip on each. Only a few bytes are read from each during boot. When I use SPIM0, 1 or 2 for them there is...
Newbie here simply trying to run some example projects from the SDK.
Setup:
Segger Embedded Studio 5.10b
Tried example projects in both SDK v17 and v16
nRF52 DK...