Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
SEGGER Embedded Studio Release 3.40 Build 2018052200.36079
The so-called "flash (sic?) placement" XML file contains two sections:
First:
which does, indeed, seem...
Hello, I am currently working on a nr52840 s140 Sdk 15.0 card and I want to recover data from a component running on the i²c bus. (I have not yet installed the component on...
Hello,
I would like to know if it is possible to use a nRF52840 as bridge between ethernet and 802.15.4/thread. For a sensor network I need an ip connection between multiple...
Hi,
I'm using nRF52 DK. I was checking the message sent by NRF_LOG_INFO() on Termite. I'm getting driver error when I try to connect to laptop's bluetooth.
Without the...
Hello
what is the maximum limit for PWM outputs pins on nrf52832? Can we use all the GPIO pins as a PWM output?
For ADC, i can see there are 8 dedicated pins , but i...
hello i am beginner in this,i am using example\ peripherals\ saadc for nrf 52832. This example code is done by using timer and i could not understand how to use timer. We...
hi all ,
i now need porting nrf_libuarte_async lib for my project . it show some error
How to deal with this problem？
i reference (experimental_libuarte project...
Hi everyone;
I wanna send to data my uC from my phone. I looked peripheral uart example. This example use only send data phone from nrf52 SoC. What can i do? How I add...
Hi All
I have developed some code by modifying the 'ble_app_multiperipheral_pca10056_s140'. I have tested my code on the NRF52840 DK board (PCA10056) and everything seems...
Hello
I have developed an application for the smart beacon and I have the following problem:
I use two diferent sets of values for the connection parameters in order to...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
We are developing a BLE Mesh product and we use the mobile phone mesh library iOS and Android for the node provisioning.
The final user will need to synchronize more than...
Hello,
We have a Buttonless custom board based on a nRF5282 with SDK 15.0.0
The DFU OTA Buttonless works fine, but to prevent the device to brick we put a physical button...
Hi all,
I am having build error of example light_switch_dimming_server in mesh sdk 2.2 that timer 2_irqhandler multiple define it is define in
D:/../../nrf5_SDK_for_Mesh_v2...
