Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi all, I have some question for ask :
I add NUS service into light switch proxy server example. And I only run nus service part (Don't run Mesh part)
when I use IOS to...
Hello All, Please help me. I have nrf52840 and added json parser which is large and nested. Json_parse fails , is there anyway to enlarge heap size?
Any feedback must be...
Hello,
I'm trying to flash wt51822-s4at using nrf52dk ( https://4tronix.co.uk/picobot2/WT51822-S4AT.pdf)
It has nrf51822 chip on board
The firmware goes through without...
Hi,
Does FDS event handler run within interrupt context ?
Can another FDS api be called from within the event handler (i.e. - calling garbage collector from within event...
I am using a three axis mems sensor and will need to computer trig functions.
If I use the math.h in the Segger Embedded Studio will it use the floating point hardware in...
In this thread https://devzone.nordicsemi.com/f/nordic-q-a/32708/bluetooth-developer-studio-plugin-for-sdk-15-0-0/126066#126066 Kenneth said there were no plans to update...
I can not debug my app with freertos and BLE if the ble is connected, but I can debug the app id the ble is disconnected, i want to debug inside the xqueue recieve and send...
I'm developing on the nrf52840PDK and I was running the cdc_acm exmaple in the SDK to observe the token exchanges between the host and the device.
In the Nordic52840 Product...
Hi all,
I have a module with nRF52832QFAAB0 IC, I'm looking for the IC revision in the compatibility matrix here.
Unfortunately I didn't find any packet variant and build...
I've run the Demo(thingy52-mesh-provisioning-demo). And it works. Now, I want to expand the function.
I 'd like to create more model(for example, sensor model for humanity...
Hi,
Sorry for post here again but i'm having a lot of trumble. I'm actually at the step 4 of the guide, which is the page generation.
I've made correctly all the previus...
I am working on a nrf51822 board and trying to run ble_app_hrs project using nrf sdk 12.1 and s130 softdevice. I converted the uVision project to the Segger Project using...
I use SDK 12.3.0 with IAR
If there is an option to know the last page that programmed?
For example:
Linker: ROM start address 0x1F000 end address 0x76fff
But...
Yesterday, I upload the thingy sdk v2.1.0 in keil uVision5 and rebuild it. After rebuild, it showed one error namely "fatal error" due to the large size(122kb). please suggest...
I am using sdk 14.2.0.I am trying to connect mpu9250 with nrf52832 dev board. whenever I took data serially on putty it is true...but whenever I try to connect it with NRF...
