Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
We used nRF5_SDK_15.0.0_a53641a and nrf5_SDK_for_Mesh_v2.0.0_src.
We are following DFU quick start guide http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
Dear Sir：
i seen the proximity example，the battery level measure is init by a m_battery_timer_id ，in my project ，
i need user multi saadc channel ，and different...
Hello, we are using the nRF52832 for building our custom board.After loading the example bluetooth_uart code given in the SDK, our board is not producing correct RF(Bluetooth...
Hi, I have a BMD-300 (nRF52) module that I'm attempting to program with OpenOCD and an ST-link from Linux (it worked great for nRF51 so I was trying to keep the same tools...
Hello,
I have been trying to have a central/peripheral device read UUIDs and RSSI values from surrounding peripherals using their advertisements and without actually connecting...
I'm attempting to add the bonding components from the ble_app_hids_keyboard example to the ble_app_uart example. I've gotten everything configured to the point where I can...
I am connected with this correct com port but Device discovery is failing to start.
First it says NO response from master emulator then it fails to start. Please help me...
Hi, I see that in the nrf52810 reference layout ( Nrf52810 Reference Layout ), all the capacitors and inductor have 0402 or 0603 footprint. i would like to switch the foot...
i followed this custom service tutorial.
but when i changed the RAM_START and RAM_SIZE address it getting below error, im using S132v5 softdevice
<warning> nrf_sdh_ble...
Are the PCB antennas provided in eagle library of NRF52810 ( github ) require any additional components for impedance matching or i can directly add the PCB antenna to ANT...
I downloaded radio_test.c from Nordic and complied it to output a .hex file. Now I want to flash this .hex file onto nRF52832. Does it require to softdevice and bootloader...
Hello (I'm new to this nRF-world...).
I am searching for a small "nRF-52832 clock" (arm mounted watch) that at least reports the "surrounding/room temperature" (not only...
Hello
SDK12.3, nRF51822
Example Gazelle from SDK works fine. If I use the softdevice (add ble_stack_init) then the program freezes in the nrf_gzll_enable
I want to do changes for firmware upgrade nrf52832 with SDK BLE_2.0.1 for the mesh.
I need DFU (Bootloader)UART for our application to upgrade nrf52832 firmware by the host...
Hi
I have written this code based on a sample from SDK12. The board is a pca10040 and nRF52832 chip. It seems like after disconnection from the master device the Softdevice...
