nrf51822 SDK 9.0
iphone 6plus System version IOS9.2
When the phone receives the QQ message "static void notif_print(ble_ancs_c_evt_notif_t * p_notif);" can execute.
but...
Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Good day. We ended up getting a bootloader based on the NRF5 using the Serial Recovery method and a non-upgradable bootloader. The update is coming from a microcontroller...
I'm working on a linux driver for nRF7002 based on the experimental linux driver: https://github.com/NordicPlayground/nrf70-linux-driver . This is being done on linux 5.13...
Is it possible to somehow set a lower charge current than 32mA for the whole charge cycle or force trickle charging for the constant current charge cycle? The issue is that...
I have a GSM application connecting to MQTT that worked previously refuse to work when I picked it up again to improve on it.
To make sure there isnt a problem in my firmware...
The following settings are required to make I2S compatible with the AK5720VT.
MCLK=12.288MHz BICK=1.536MHz LRCK=32kHz Bit length=24bit
CONFIG.RATIO >= 2 * CONFIG.SWIDTH...
Hi All,
I have recently design my version 2 of my custom board, everything seems to work on the board, the firmware is fully running but i can't see the BLE device on...
Hi,
I tried to send audio with a sampling frequency of 44100hz, up until this point I had been sending the default sampling frequency of 48000hz.
For this I change the...
Hello,
I am trying to make radio test functions work on my 52840-based board using SDK 2.5.2. After some effort I managed to create a simple test program that partially...
I want to use P0.00 and P0.01 as UART pins. I have shorted the SB3 and SB4, and opened the SB1 and SB2 for using the pin as GPIO.
If I am enabling the " CONFIG_BOOTLOADER_MCUBOOT...
Dear Sirs!
I need that low power comparator on input AN7 reset controller when device is in OFF mode when voltage on pin drop below threshold.
Controller powered +1.8V...
Hi
I have a project base on Nordic sample code "v2.5.0/nrf/samples/cellular/Location" and it fully work with SIM card
now I need to use Onomondo softsim to replace SIM...
Hello, I'm getting these series of events often when the client is sending data to client. This is the the nRF SDK 17.
If I add a delay on the client app that is talking...
Regarding the description key Page 10 of the document "nRF Sniffer for 802.15.4" states "00112233445566778899aabbccddeeff", but does it differ for each device? Also, if there...
Hi there
During updating nRF5340 over bluetooth, really rarely the CPUNet fails to be updated over bluetooth.
The mcuboot says: Image in the secondary slot is not valid...
