Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
Hello,
I have followed the steps here: https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/installation.html to install toolchains and SDK on a fresh Ubuntu 22.04 computer...
Hello everyone, I'm learning about MCUboot. Currently I have tried searching for information online but still don't have an overview. So I hope everyone shares their experiences...
I built blinky which just blinks a light, pretty simple :). Then I found Anroid nRF blinky in your git hub repo, that's a git hub project that remotely blinks a light. But...
In which subsequent process is the random_static_addr_cfg function reflected? Does the ID change with each build? If the ID changes, will it affect Bluetooth connections?
Due to project requirements, I have made significant modifications to MCUBOOT, but currently all projects use the same MCUBOOT file. Is it possible to have MCUBOOT configure...
I'm going to build an project with 2 AS5600 sensors, and also using I2C mux(TCA9548A) to communicate with 2 sensors.
I have some problem with devicetree. There are two errors...
Hi!
I used SDK15 (may be 15.3) with s132_nrf52_6.0.0_softdevice
I used nRF52832 in two modes in one time.
When I stay in connect with my peripherial to a central device...
Hello,
I have a custom board with a nRF5340 on it. The firmware gets built with MCUBoot in serial recovery mode to update the application core. The serial recovery mode...
Hello,
I recently purchased a few NRF9161-DK boards for both LTE and NR+ evaluation. However, I am unable to run through the initial demo. The board is discoverable initially...
Hello. I'm using serial lte modem as mqtt client.
After a while I receive fault. Adding logs:
#XMQTTEVT: 9,0 ESP:LTE: PINGRESP packet #XMQTTEVT: 9,0 PINGRESP packet CR...
Hi, I read somewhere that the LOG module works differently from printk() and uses a separate thread or so. But I couldn't find any information which priority this thread uses...
Hi there,
I am currently having issues flashing an nrf52840 DK on windows 11 using either west for a Zephyr project or nrfjprog. I have successfully done this on a work...
Hello,
I am designing a custom PCB using an nRF5340 and am unsure what my options are for how to program it.
I've seen a number of forum posts saying that you can program...
I've been working for a year now programming nRF5340 DKs using nrfjprog and I still can't seem to figure out what is the right way to program them. It is also very random...