I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Board: nrf5340dk (build board: nrf5340dk_nrf5340_cpuapp) / SDK: v0.16.8 / I'm a complete beginner who touches the nrf board for the first time My Project: max30101 --(measured...
Hello
we have some own created UART drivers which access the UART registers directly.
Those drivers have been working withe the older chip revisions for years.
Currently...
Hi,
I cannot resolve the problem while setting up modem trace RTT logging. I'm also unable to find up-to-date information on how to set this up.
I have connected DK as...
I'm close but this is not working for me yet. I'm trying to send a few hundred bytes from android to my nrf device. So I tried to implement long write where you set prepare...
Hi I've a side request, into the exercise I've to perform some changing into the DK programming interface through the JLink, so the question is how to restore the predefinite...
I am getting an fs_close() -5 error (-EIO) when I write to an SD card using fatfs. I determined this error was associated with FR_DISK_ERR in fat_fs.c.
Additional info ...
Hi,nordic team，
im use nrf52840 develop my product with sdk ncs 2.6.the speed of desktop dfu is so slow,and the speed of configurator channel is also slow.i want to transfer...
Hello. I am facing an issue in configuring ADC for multichannels. I was looking at the Nordic fundamentals course Lesson 6 Exercise 2 .In this example, the adc is configured...
I was working through Nordic Intermediate course lesson 8 exercise 2 - DFU over USB, adding external flash and custom keys. I was using an nRF5280DK. (Sticker: PCA10056 2...
I have been trying to implement a DFU OTA using Bluetooth Low Energy from one nRF52840 DK to another nRF52840 DK using the smp_client_ble ( https://github.com/hellesvik-nordic...
hello.
I am using nRF52820 and nRF5 SDK (17.1.0).
When the fds_gc() function is executed, all bonding information in the pairing area (flash) is erased.
My understanding...
I'm using CYCCNT to time code. Works fine until APPROTECT is set, then after reboot the CYCCNT is always 0. Is there a way to enable CYCCNT when APPROTECT is set?
I'm using...
Hi everyone!
Setup:
Currently, I am using the nRF52840 DK board to evaluate neural network models directly on the nRF microcontroller. To measure the power consumption...
Hi!
I'm using an external flash (SPI NOR) to store the secondary partition slot of MCUboot. According to datasheet, the SPI NOR chip in use supports 4KB, 32KB and 64KB paging...
