Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
on your item nRF52-DK
there are differents between Resision 2.1.1 vs 3.0.0?
V 2.1.1 ==> Chip ATSAM3U2CA-AU of Microchip is alone to provide "programmation/debugger segger...
Dear Mr/Mrs,
Our commercialized product currently have a default: some (luckily rare) clients get a crash after the 1st configuration - sometimes hours after but always...
hi support team,
customer 52832 product had problem that they can't pass fcc test,the reason for this is they forgot to add capacity to those pins.
their design is:
...
Hi，When installing the nrf5340 development environment, the tool chain is installed and the "getting started assistant" check is also passed. However, there is no NRF related...
By default the Thingy91 has many useful factors it can measure:
Pressure, Humidity, Temperature, Light, Position, Button, Flip, Signal, Voltage ...
I really only need...
Hello,
I want to design a board with nRF52832 or nRF5340 which contains several sensors, QUAD or regular SPI flash memory, and a TFT LCD. This TFT has an SPI connection...
Hi,
I am new to DevZone as well as BLE development itself. I am currently working on a project and trying to undestand the IDE as well as the processes and workflow of the...
Hello Community & Nordic support, Observed behaviour: my project build with nRF Connect SDk v2.1.1 was with errors
expected behaviour: my project build with nRF Connect...
Hi,
If I run my nRF5340 peripheral BLE NUS service with NCS 1.9.2, I get two different behavior at console.
When I connect from my WIndows PC running nRF Connect for Desktop...
I'm not sure if this code I inherited is using k_poll_signal correctly because it seems like I can handle it in a much simpler way with an atomic variable.
The below code...
I want to use the lsm6dsox IMU on my Adafruit feather nrf52840 sense board, and I should use other I2C, other than p012 and p011, to not have a problem with the other IMU...
Dear team,
I am not able to flash the nrf5340 audio application (gateway) to the nrf5340 Audio DK using SWD from nrf5340 DK. I nrf5340 DK outputs 1V8 logic.
I can see...
I am using S132 in the Segger IDE on an nrf52832.
I am using SDK version 17.0.0_9d13099.
When I call sd_ble_gatts_hvx() from within a GPIOE ISR (externally pin triggered...
Hello,
Looking to see if there is a pinout TABLE for this package. I've seen the schematic drawing already but looking for a table format which is more user-friendly when...
