I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi. I got the message when I download serial dfu using Jlink debugger and nrf Connect desktop.
this is capture from jlink rtt viewer.
I uploaded not modified example...
Hi,
We are looking at how we software upgrade the device during its lifetime and assume that a bootloader will be required on the AP and the NP to allow us to load a new...
Hi Nordic,
I have learned about both the DTM and radio_test example source code. For our prototype tests, I think the latter may be better for us.
I have tried to wirte...
Hi
Is there a possibility to update the bootloader himself over the BLE DFU?
I have a new bootloader with a bigger size (MemoryMap changed) and I am wondering if I can...
Hello,
The following error message appears when the original code "asset_tracker_v2" under NCS 2.0 is compiled with vs code IDE,
Can anyone give me some comments? Thanks...
Hello,
I'm just trying to run the LTE_BLE_GATEWAY sample program and I've flash all the nessesary firmware onto the nrf9160dk baord. However, when I turn on the nrf52, it...
Hi,
I am building the CoAP client and sever example programs on a third party module (Reytac MDBT50Q). I am using Reytac dev board MDBT50Q-DB-40. Unfortunately the example...
Hi all
Can the NFC tag of nRF52832 be integrated with multiple cards？
Such as t he access control card of my dormitory and my home can be replaced by one card
Thanks...
I use the connected mode of DF, i use the two receiver,one transmiter,but when i flash the procedure to my boards.i find that only one receiver can get the IQ samples.how...
I am trying to port some code I wrote for Gazell, which I guess acts more elegant since it uses PPI, a workqueue, timeslots, etc. I have an ESB connection in which I receive...
Hi,
I am currently developing with the nRF52 DK (nRF52832 SoC) and the nRF52833 DK (nRf52833 SoC). I have built and flashed the Bluetooth: Peripheral HT sample from Zephyr...
HI,
I'm using nrf51822 and Gazell protocol.
from the RM, i get that the combined length of S0, LENGTH, S1, and PAYLOAD cannot exceed 255 bytes, which i think i can set the...
hello everyone, recently I entered the world of nordic,
and I have been testing some of the functionalities, of one of the devices,
specifically the nrf5304 dk model,...
Hello,
I created a device on AWS and corresponding certificates/shadows on the us-west-1 server. I'm able to successfully connect and send to this endpoint, but want to...
