Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I'm using NRF52833 with SDK v16.0.0 along with mesh SDK v4.1.0. I want to know if it's possible to write data which is not word aligned into the internal flash (For example...
Hi everyone,
I started working on nordic nRF52832 DK and tested out some examples. I think i am done with the examples now and am looking to write my own code apart from...
Dear Members,
How can we determine the first ANT message from my transmitter ?
We saw from ant_parameters.h,
Which variable is being used ?
Kind regards...
Hi,
Today I found that after I OTA my board, it runs well at first. But when I reset it, it will run old image again.
Before this OTA, my board has gone through many OTAs...
hi all,
I am currently working on a ble project, the led based on the NRF52832 chip is used as the slave, and the mobile phone is used as the master to form a star network...
I use nRF Connect to connect to nRF52832 device. 1st connection is bonded authenticated encrypted link, but 2nd connection becomes not bonded unencrypted link. Why 1st and...
Hi,
I was provisioning devices for a customer today when I noticed at the end of provisioning that the JSON database file that was exported had all the features except ...
Hello,
We are developing a library which is intended to use the trustzone feature available with nrf5340 DK. We followed the instructions available in Using a custom Secure...
Hi
When I use the nrfjprog with the command line:
The application is starting and the code running.
If I do the same again (with the same hex or a newer one) the...
I am developing a project with nrf mesh SDK 5.0.0, I use dimming code, but the code uses rtt input, if I want to replace rtt with buttons, what should I do? I'm learning,...
Hello! I will try to make this as simple as possible with the details regarding this issue What I have
nRF52840 DK (pca10056) (As BLE sniffer)
nRF52 (pca10040) (Used...
Hello
We are using NRF9160 AssetTracker 1 and MQTT to AWS. We have a AWS Certificate, Root Certificate and Public and Private Keys on the device.
We want to start testing...
My device get deep sleep mode. It wakes up from reset button trigger. Because I couldn't gpio pin trigger for wakes up. So I put vibration sensor to reset pin. It wakes up...
Hello, I am developing a custom board based on nRF52832 that should spend most of it's time in SystemOFF mode. Eventually, it will wake up on an GPIO event caused by the external...
