I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hello everyone,
I am designing a Bluetooth repeater that will be powered eather by USB or an embedded Li-Po battery. This device will run with the nRF52833 along with...
Hi,
I am working on a project, where I am trying to create a touch LED project using NRF52832. I have completed the prototype, its working is quite simple. The LED will...
Hello, guys!
We are using nRF51822 SoC with nRF5 SDK v12.3.0 and s130 SoftDevice. One of our desires is to use Software Interrupt (SWI) driver.
However, when I try to...
Hello all,
I am configuring a low power application for the nrf52832 board (custom board). This is a very low power application and I want the board to stay on sleep mode...
Hello everyone, I am working with a BMI160 6-DoF sensor. I have some drivers related to this chip. Using the Segger J-Link debugger the drivers just work fine without any...
I update a couple of device to mfw_nrf9160_1.3.2.zip.
Before that (1.3.1), my experience was to get a ENETDOWN, when calling " sendto" while the device has lost some the...
Hi.
I'm trying to add Bluetooth capability to the "Asset Tracker V2" project. I was able to do it on the nRF9160DK board. I could not find a working example to make the...
Hello,
windows10 x64.
i have used NCS1.9.1 and NCS1.9.99,now i want update to 2.0.99
how to install NCS2.0.99?
because nRF Connect for Desktop Toolchain manager no...
Hi,
1. How to calculate the Flash and RAM usages at runtime? I am able to do it static way but wanted to analyze this at runtime.
2. How to calculate the Heap usages at...
Hallo,
currently I try to optimise the functionality of my extended advertiser code. I found that there are also some call-backs defined for extended advertisers. The struct...
I use iOS nRF Connect APP to test DFU. But it failed with writing is not permitted.
The following is log message of nRF52832 device. 00> <info> app: Inside main 00> 00>...
Hi,
I am working on a system that runs a proprietary protocol, i.e. non-BLE, which works fine when it uses either uncoded links or S=8 ( LR125Kbit ) coded links, but I want...
Hello everyone, I am trying to send a string printed float number using the ESB protocol. I am using nrfConnect SDK 1.9.1 with nrf52832, started off with the supplied esb_ptx...
Respected,
I am using NRF connect for desktop for programming my actinius sensor (ICARUS IOT BOARD) but whenever I want to upload and reset the board using actinius programmer...
