Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
We recently changed from nRF52832 to nRF52833 and for layout convenience used some of the P1.xx pins for our signals.
We are using SDK ver: nRF5_SDK_17.0.2_d674dde
For...
Just installed nrF Connect SDK v1.8.0 (using Toolchain Manager) - under Windows Windows 10 Entreprise
I have completed the setup and restarted my PC, however VSC is not...
Hi everyone,
I experiment with the saadc low power example . I have followed all the settings but I cannot achieve as low power as the example. As you can see from the PPK...
Hi,
1.How to test the ESD Human Body Model (HBM) performance of nRF5340?
2.How to test ESD Charged Device Model (CDM) performance of nRF5340?
Thank you for all your...
Hi everyone,
I have just purchased the PPK2. I've noticed that there two methods two measure the current
1. Source meter (the PPK2 provides power to the DUT)
2. Ampere...
Good day!
I have a question about length in MPID. In current implementation size measures in uint16 size and this brings lot's of troubles when you try to decode values...
Hi, I want to run UART on my custom PCB module that uses Wuerth Elektronik Thyone-I module that has nRF52840 chip. The project has just a RX, TX pins (and power supply, of...
Hello,
I'm currently having some issues where my custom board is either experiencing infinite DFUTarg cycle or "no bootloader was found" error.
I have been following the...
Hi,
I'm trying to run some example with ble fota
I've read
http://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_nrf52.html#fota-upgrades
and
http:/...
Hi i am using nordic nrf52840 chip.
i programmed one application at 0x27000 address, and now i want to calculate the size of that application code in run time.
i have...
Hi
I have a project as the follow
What I have done:
1. Compiled app.hex ( Configured with my board), works fine.
2. Compiled bootloader.hex ( Configured with my...
Hi, I've adopted the DFU part of the NRF Toolbox app in my own app. I want my app to be bi-langual (English / Polsih). I can do this for all the texts that I've created, however...
Hi,
I had a temperature adc reading accuracy issue in lower temperature such as -40.
It is similar to this post issue ( https://devzone.nordicsemi.com/f/nordic-q-a/80859...
