I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi Nordic experts,
Recently, I tested and found that I failed to start the advertisement with NCS 1.7.0 if the length of advertising data is greater than 251 Bytes, for...
Dear sir/madame
Start & stop of advertising and how to prevent automatically restart of advertising in case of a random disconnection or disconnection initiated from the...
Hi,
I've been scowering the SDK dicumentation and DevZone for this information without finding it. My apologies if this has been answered before.
When using the SUPL library...
Hello!
is it possible to execute some code in the section
or do i have to implement some kind of thread logic? or any kind of nonRTOS library?
I come from FreeRTOS development...
Hello,
The Example code is running, but only printF() statements are printing and to the PC terminal program.
The example calls for softdevice build 122.
I "think...
Hello,
I am working with the Thingy91 device and the SDK v1.3.0 asset tracker example (I am not interested in upgrading at the moment). I would like to know how I can save...
I flashed my board with DTM image, assign P0.20 for TX and P022 for RX. Most of the times the DTM application can't communicate with the nRF5340, maybe 1 out of 20 times,...
Hello,
I used to import our current project to segger embedded studio v5.62 from keil so I'm followed these instruction .
All project files are compiled well but problems...
On the nrf52840 module, when I first output to one of the GPIO pins when I load any softdevice ble_peripheral instance I have installed. 10 ms after the VDD pin is energized...
Hi,
I have nRF52840 DK, and PPKI power profiler, I measured peak current mA using PPK on Radio Transmitter, And I found there is a big discrepancy between measure and typical...
Hi Guys,
We are currently working on a mesh sensor network. I have already developed a vendor sensor model (client and server). The client will also work as a gateway and...
I have a couple of questions regarding the nRF52840 internal voltage regulators, specifically REG0. I couldn't find the answers from the datasheet and therefore I hope that...
I started using nRF Connect for VSCode a couple of days ago on one computer and it has been working great. Now I had to switch to a new computer where I had also just briefly...
The first chip silkscreen for 2050ST second chip silkscreen is 2109XN third silkscreen is 2052TJ, transmit power configuration for 8dBm actual test from the chip side, test...
Hi, i'm using STLink V2 for compiling the code, the weaknes of this compiler is you can't see the result debuging or serial print output.
so i'm using USB TTL to see output...
