I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi, I am trying to achieve the lowest current consumption possible on the nRF9160-DK, which should be about 1.4 uA in modem shut down state. Unfortunately, my best result...
Hi all, I want to form a thread network.
I have BorderRouter [Raspberry pi 3B flashed with Nordic alpha 4.1.0.1 image + nrf52840 dongle in NCP design] and is up and running...
Hello.
This issue was tested with nRF5 SDK v17.0.2.
There are steps to reproduce :
sdk_config.h should not be included in nrfx_clock.h. It's a default template by...
Hello,
I am looking for some help solving a peculiar issue with eddystone beacons, the nRF52805, and some cheaper Samsung android phones.
System Description: - I am using...
Hello,
I have been running this program without any problem then I added some code to read and write to flash using NVS when the error shown below appeared.
I am running...
I have been using the Toolbox to load zip files to a device. Now the toolbox uploads a file and 'say it is complete', but the file status in the menu window say file not loaded...
Hi forum,
I am working on nrf52832,using sdk15.0.0.
I referred TWI_sensor example as reference for sesnor interfacing. Individual sensor works when i trired to integrate...
Hi,
I am using an NRF 51422 DK, SDK 12.3, and Soft Device S130. I am also a beginner to development with Nordic Products, and RSSI collection in general. I am using the...
Hi Nordic team, I'm working with nRF52840 PCA10056 , base on Thread_Zigbee_ v4.1.0 , and light_control example. I modifed, try to add temp_measurement ZCL in all light_bulb...
Hi ,
My environment:
nrf5340 dk board
nrf connect sdk
segger studio IDE
.
I want to test spi loop back without any connections.
I don't want to connect any...
Hello, zephyr pwm driver documentation and samples , shows clearly how to generate a PWM output using nrf52840 dk. However, we need to synchronize the PWM output to an input...
Hello, how can we configure the counter in an nrfx52840 dev board to count pulses on an input pin in zephyr? There is a counter driver in zephyr, but there doesn't seem to...
What I'm trying to do, is probably very simple. I hope.
In the following code which works fine.
I want to scan not using Coded PHY
Then change back to using Coded PHY...
question here, I am using nRF52840 device with zephyr application & MCUboot + SMP service the DFU is now done using: https://github.com/apache/mynewt-mcumgr-cli or using Nordic...
