I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hi,
I am using ppi to read some continuous data from a sensor through SPI and i got it working, it reads data in evry 8ms from the sensor through ppi.
but it fails when...
I am working with the secure bootloader example. I copied the firmware zip package to my phone. It contains only application.hex in the package, there is no softdevice or...
Hi,
I am working on an application where the device will be in off mode(only timer and BSP initialized in main ) initially and when I long press button_0 for 5 sec the remaining...
Hi,
We are looking for DFU mode GATT protocol source code for reference to implement custom android application which uses DFU mode GATT service to update firmware distribution...
My static code analysis tool complained something, so I took a deeper look and found the following declaration inconsistencies as of nRF5 SDK v17.0.2 in the DTM area. So I...
I am in the process of programming the MAX30105 sensor with the NRF52840 board to obtain the oxygen concentration values I tried to use the library that already exists in...
Hi ,
I am trying to connect my NRF52840 with the application NRF Toolbox using bleuutooth technology when I use this DK
it works very well and the application detect...
I have an nRF5340 DK board. I have followed the online installation instructions and *believe* I have successfully installed (win 10) nRF Connect and Segger Embedded Studio...
Hello, I'm routing on the nRF52833-QI. I want my RF track (ball H23) to go without bends. I don't use J24 ball. Can I remove the ball J24? What is your suggestion? Best regards...
Dear Sir,
Moving to zephyr new installation 1.4.99
The code of getting the IMEI number no longer works.
Modem firmware is mfw_nrf9160_1.2.3
reply_buf_len = at_exec_reply...
I'm trying to connect a 52832 board to a peripheral BLE device. NRF52832 SD: s132 v7.0.1 SDK 16.0.0 As a first step, I'm not setting flters, I just want to connect to any...
Hello,
We are using nRF52840 with SDK 15.2.0, a bootloader and the SoftDevice 6.1.0. We are able to perform a DFU for our application by downloading the .bin and .dat files...
The nRF53 data sheet defines the minimum clock period for teh SPI slave and master as 125nSec - which equates to 8MHz. The SPI Slave also gives the max data rate as 8MHz with...
I tried out a ble_app_hrs_freertos_pca10056_s140.emProject and was able to compile but a couple of questions:
- how is heart rate info calculated? where's the sensor even...
Hi,
I want to write to the NVMC UICR Customer[n] memory addresses during code execution.
I noticed that I can write/read/erase those addresses only before the initialization...
