Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I'm using Zephyr on a nRF52840 and I'd like to use the QSPI with the Fat Filesystem. I added the following Config statements to prj.conf:
The nrfx QSPI driver and file...
Hello,
I am wondering where to change the baud rate for the UART in the NRFConnect SDK using zephyr. I am working with the peripheral_uart example.
Thanks,
RJ
Hello,
i just migrated from nRF51 to nRF52. I tried to implement my custom service. I followed the tutorial from this site: https://github.com/bjornspockeli/custom_ble_service_example...
Hello,
in our application we have two devices. A nrf52840DK as central and a BMD-300-EVAL (contains a nRF52832 chip) as peripheral. We need a timer/counter that generates...
Hi,
I had used nRF Connect Programmer to flash nRF Sniffer firmware on my nRF52840 Dongle, but after that, when I tried to flash the firmware again, I found that there was...
Hi,
I want to add new peer to peer manager using pm_peer_new().
pm_peer_id_t p1 = 0;
pm_peer_new(&p1,&bond_info,NULL);
there are no peers, so trying to add as peer_id...
Bought 2 nRF5340 DK kits from Mouser. Followed the setup instructions and fell at the first hurdle. Attached NF antenna, connected to USB and switched on.
Nothing. Green...
Hello,
I am currently working on a project that requires data to be sent over Bluetooth. I currently have an NRF52832 Development board and have been trying examples and...
Is there any difference in terms of RF performance between different hardware versions of nRF52840? Can someone point me to the relevant documentation?
Thank you
I am working on the nRF52840 DK board SAADC module with nRF5_SDK_17.0.0 SDK, and I am unable to get the output on RTT.\
I am working on the pre-prepared program from the...
Click DFU after connect. Navigate to folder. Click .zip update file. Click OK. File name does NOT appear in chosen text box, box remains empty. Works correctly on English...
Hi everybody, I'm trying to set up my 52840 DK to scan for BLE_GAP_PHY_CODED advertising packets from 52840 Dongle. I think I was able to program the dongle, because it doesn...
Hello,
I've been tasked with adding radio test functionality to our manufacturing support firmware. I reviewed the comments here on devzone and studied the radio_test...
Hi,
I am currently working on an application for nRF52810. It has only advertising feature and I calculated the consumption with online calculator. The values I got from...
Hi, NODRDICSEMI
Now I use PPI + gpiote (spidma) to make the hardware read and write by itself. But after I enabled RX list, I found that when the amount of data read exceeds...
