I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
I'm using nRF51822_xxAA , with SDK12.3.0 and Softdevice S130 v2.0.1 on Keil V5.29.0.0. And as a central I use Redmi 7A phone with Android V10. I want to sample ADC @ 200Hz...
Hi，all:
There is a question when I run usb_msc example on nrf52840DK(sdk17.0.2)，I do as following steps,
Then,after I press button 1 for serial times,I found there are...
I want to get started with nRF52832 in Arduino. I have a Ebyte development board with E73 module containing the NRF chip.
The hardware is quite similar to Adafruit NRF52...
Hi,
Hope you are doing well!
I am trying to do Buttonless DFU on our own Android APP. I have finished programming on nrf end and succeed doing DFU on 'nrf connect...
Hello, I have done customized board using nRF52832 and when I try to flash code using nRF52 DK(Jtag) it is showing following error. could not fetch memory size of target devkit...
Hey all - I'm new and trying to connect Thingy91 to nRF Connect V3.6.1 for the first time. When I open the Programmer app I only see "No devices available" in the drop down...
Hi,
I'm trying to follow the NCS tutorial in: https://devzone.nordicsemi.com/nordic/nrf-connect-sdk-guides/b/getting-started/posts/nrf-connect-sdk-tutorial---part-1-ncs...
Hi,
we are developing a custom BLE communication. For this we are using:
- nRF5_SDK_17.0.2_d674dde - s332 - based on BLE NUS UART example
Everything works fine, until...
I'm trying to open a NCS project in SES but I'm getting error 1 from create_nordic_project.py. NCS 1.5.0 installed with toolchain manager on macOS 11.2.2
The error in SES...
Hi,
I am following a client case that they have issue on accessing SD card via SPI port.
I used the sample project fat_fs on nrf9160_pca10090 DK and used SPI_3 to access...
nRF9160 DK schematic sheet 2 missing pin names for WP and HOLD of nRF91_EXT_MEM in the On-board interface (far right page 2)
could someone post what nRF9160 pins are used...
Hi,
I have written one application with logging disabled to save power.
However, when I tried to debug the code with Ozone, during startup, it raises BusFault exception...
Hi,
I am currently working on generating a dfu over serial uart by testing with the ble_app_blinky example given in the SDK 15.2.0. Currently the ble_app_blinky hex file...
Hi ! Using nRF52840 whith SD140 as central and 6 link count I research :
changing the NRF_SDH_BLE_GAP_EVENT_LENGTH from 6 to 2 does not change "Window size" on CONNECT_REQ...
Hi,
I messed up my SES project and now the debugging session doesn´t start and the debugger does some weird stuff and doesn´t execute my application.
I also tested if...
