Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
Dear Support Team，
Based on SDK15.3, nRF52832, follow the instructions to run the DFU process, use the mergehex.exe tool to merge settings, app, boot, and sd into one hex...
Hello everyone,
I currently using this lib: GitHub - Martinsbl/nrf5-mpu-examples to read data from MPU9255, when I'm using the easydma for accelerometer and gyros its work...
I am using the PSA library for the nRF340 and trying to use persistent keys.
It all works without persistent keys enabled, but if I add the following two lines to the prj...
Hi. I am trying to start programming our own development desk with modul ACN52840 (SoC nRF52840). I can provide schematic of development desk in private message if needed...
Hi,
I am develloping advertising configuration and would like to use the fast or slow advertising mode.
In the ble_advertising.h, it seems that the limit are an uint32_t...
Hi,
I am performing several "mlme_reset_req()" on a nrf52840 during runtime without problem, for the most part.
However sometimes the radio stack will stop after a ...
Good day
I noticed that the NFC tag reader sample is not compatible with the nrf9160K. Is there a reason for this ? will development be possible?
Thank you!
Hi Nordic
I downloaded nRF5340 DK Hardware files (Altium Designer files).
pca10095_sheet1 and pca10095_sheet2 can be imported in PADS logic tool.
But, files from sheet3...
Hello,
I have a problem when I send data with CDC ACM and using CLI interface my data is mixing. If I put a delay between sending data I have no problem but this solution...
Hi, I want to enter the NRF52 into a standby low power mode.
I am running sdk17.0.2, with FreeRTOS and softdevice (7.2)
The steps I take are:
1) stop all my threads...
I'm trying to integrate the following driver into my project
https://github.com/nobodyguy/HX711_zephyr_driver In order to load it I need to update the west manifest. Using...
Hello,
I am working with the nrf52840 chip, and would like to store a serial number on the device that persists across boots and OTA-DFU. I have integrated the nvs sample...
Dear All:
We run a simple message model in light_switch_client and light_switch_server code.
After provisioning the two nodes via nRFmesh app and set pubilsh in clent...
Hi,
We need to refer detailed documentation & implementation for health model struct bt_mesh_health_srv_cb
we referred to this document - https://docs.zephyrproject...
