Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
Hi,
I want to set up a set of four PWM signals that are delayed at a specified interval, just like how the stepper motors are run but the falling edge of the previous...
Hello all,
I am merging the buttonless DFU example with my application for nRF52805.
Everything is well, but I am running out of flash. I am therefore trying to reduce...
We are currently running v1.4.1 but want to move to the new revision (R3) to gain the RF immunity and security features.
Do we need to move to a new version of Zephyr to...
Dear all,
I've been adjusting BLE data sending mode to increase BLE throughput but have some problem using queue.
Here are some basic ideas of my development:
Keep...
Hi,
I am working NRF52840 Dongle board, I am using ble_app_uart program with some custom code, from that I am facing some problem while connecting the device in nrf connect...
Hey All,
I am using a non commercial license of SES (v6.30). Initially as PoC I built code with a TX/RX combination using the examples/peripheral/usbd_hid_generic/ for RX...
Hello Devzone,
I want to incorporate DFU in my project for the microcontrollers I am using. I have a nRF52840 which is my main controller and to it I have a nRF52832 connected...
SAADC feature request: RESULT.PTR auto increment Right now, continuous sampling works well for a high sampling rate (up to about 200ksps), keeping DMA etc active to cope with...
Hi,
Im using the nRF52840 DK and im trying to set the Service and characteristics with this tutorial : https://github.com/NordicPlayground/nRF5x-custom-ble-service-tutorial...
I have one light sensor model publishing light lux level of the room to Group A . On other hand, have occupancy sensor publishing to the same group A .
and one light with...
Dear All, I am working on an application where I am connecting to the network, sending some data and then disconnect using CFUN=4, in order to achieve low power for my application...
Hey Nordic's technical team,
I'm trying to write and read via I2C to a component with two bytes registers. I tried the following method:
Then switched to this one: ...
Hello,
Using v1.9.1 nrfConnect and the Coordinator example on a nrf52840 -DK. From Nordic docs: I think I may be miss interpreting Zigbee Cluster spec... Below is example...
Good day
I have noticed that on my new DK boards if I touch VIO REF on P20 the PCB resets or stays in Reset if I keep touch the pin. My older boards never use to do that...
