Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am currently running some tests on the Legacy DFU protocol and notice that even valid firmware images are unable to be transmitted. My setup is as follows:
Peripheral...
Hello,
As shown in the question. I am testing the ncs bootloader b0 and mcuboot, but I don't know it's ok or not.
work condition
ncs: 1.6.1
board: PCA10056
I am...
Hi
I have a strange question to ask for your help.In my program, I define and use a large number of global variables. However, when I define a global variable again and...
Our application frequently changes the channel table when we find interference in multiple channels. So changing channels frequently (because of high interference) causes...
Hi,
I'm evaluating BLE power consumption with a PCA10040 nRF52DK and a PPK, I cut SB9 and did nothing else with DK.
No peripheral is used in projects, Buttons or LEDs...
Hello
I've read several post about the problem regard the printf and float numbers, such as this ( https://devzone.nordicsemi.com/f/nordic-q-a/30535/nrf52-printf-float-in...
Dear sirs/madams
I am using SDK 17.0.2
Situation:
One Central unit (nRF52840) and one Peripheral unit (nRF52840) have established a connection (NUS service).
When...
I plan to buy some nRF5340 . I only see 1 chip image from the Nordic Official Website . However, when I clicked on " distributor ", I saw nRF5340 has many different part numbers...
Hi Nordic team,
I am trying to implement DFU over uart in nRF52832 using SDK 17.0.0. My device has nRF52832 and main MCU in it, and I would like to do DFU from main MCU...
Hi
I play with watchdog.
After a watchdog reset the debugger does no longer stop on a breakpoint or generate a hardfault on a __BKPT()
How can I config the Chip to handle...
I have tried nrf_mesh_disable(); but it does not turn off the Provision Beaconing.
mesh_provisionee_prov_listen_stop(); does the trick, however I am struggling with re-enabling...
Hello
when hardfault is happaning, I can catch and understand the reset reason easilly, by looking at the map file
however, from time to time, I get a reset without...
I'm using Segger Embedded Studio version 1.6.0 to try to do some testing with SPI for a future project. Currently I am adding SPI functionality to the "Blinky" example: I...
#define SCAN_INTERVAL 0x00A0 /**< Determines scan interval in units of 0.625 millisecond. */
I am a beginner in this field. I am not sure what does this hexadecimal number...
Hi team:
After my device runs normally for more than 10 hours, the issue that THE socket cannot be created occasionally occurs. Once the issue occurs, the socket cannot...
