I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi, Nordic staff.
I'm working with Central device using S132.
There is a peripheral device using S112 in Nordic. I didn't make this peripheral.
My question is...
Hello all.
I have a question relate to: How to "ble_app_hids_keyboard" app can connect multi device?
My task: make equip peripheral base on nrf52811/840 can Adv and connect...
Hello, I am new to Nordic, I was previously using Cypress CYBT343026-01. But there were some drawbacks found during development. 1. It was consuming 315μA at 0 dBm BLE tx...
Perusing the GCC linker script supplied as part of SDK v16, I noticed that the .data section is specified as follows:
.data : AT (__etext) { __data_start__ = .; *(vtable...
I now need to burn the app firmware and modem firmware of multiple 9160 chips at the same time. Using pynrfjprog to write a program to burn the firmware for ten chips(Open...
Hello
I'm going to use a potentiometer to control the pwm. I am using a 10K potentiometer and have used a saadc example.
I printed out the value of adc through this example...
Hi everyone,
I've just been working with NRF52833 and nRF5 SDK for Thread and Zigbee v4.1.0 to create a zigbee mesh network for home automation. My network is pretty simple...
Dear Members,
I saw this code ,
If there is no input, how can I handle it and display result = 0 and not shutting down CPU ?
How can I display 0 from this code...
Hi.
I want to disable the TWI master's internal pull-ups on SCL and SDA. So I set it according to the contents of the following URL, but the setting is not reflected as...
Dear Nordic Support team,
Currently I am in the process of adding the USBD_CDC_ACM driver code to our existing application following your usbd_ble_uart example. I can receive...
Hi，
Our customer is using nrf9160.There is a problem about powem_on circuit .
Attach is the schematic diagram:
Here VBAT is 4V,PW_ON is connecting to the nrf9160...
Hi,
I'm using nRF52810.
And i'm trying to measure battery level using saadc.
The problem is saadc result is not accuracy.
When battery voltage is 3.3v, saadc value...
Have a brand new Thingy 91, latest modem firmware and asset tracker firmware: thingy91_debug_ltem_2020-10-30_5522ca2b.hex.
But within the LTE monitor app, nothing shows...
