I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i am already using sdk 10. but when we have build boot-loader program. so, generate "nrf51422_xxac.hex" file. it's working for only nrf51422.. but not for nrf51822. so, how...
Is there any difference in RAM overhead with the new app_timer module on SDK 10?
I'm my application on SDK 6.1, I have 25 app_timers which run without any issue.
APP_TIMER_MAX_TIMERS...
I am setting up production testing of our product to do RF testing per app note AN34. We are using the nRF51822 on our product. I'm using Nordic's development kit and their...
Hello,
I am planning to use the nRF51 device in DTM and was looking for help on how can use it to control via USB/UART connection to PC using FTDI chip. All I want to do...
Hi Nordic,
I am having a problem with linking against either of the gazell gcc libs (gzll_gcc.a or gzll_sd_resources_gcc.a).
I'm using Yotta (MBED) and have taken the...
Hello,
we have an android/iOS app on a phone that is connected to my button (nRF51) and to a Bluetooth headset. The app is a kind of walkie talkie that transmit mono audio...
Hi, I'm working on a project where I'm trying to make an nRF51822 play a basic sound (such as a beep). Is there a recommended DAC that should be used with this particular...
hi, i am using nrf51822 version 2, SDK 6.1.0, softdevice version 7.3.0.
because the nrf 51822 is version 2, i have no choice but to use SDK 6.1.0 not 11.0.0(latest version...
hi,
i am using ble_uart example for send 3 byte (midi format) of data over uart.
i am receiving data which is appended with past data and sends as a chunk of data around...
Hello, i'm making small android application for my own test purposes. I want to understand full structure of advertisement packet which i receive with my phone. I can't find...
Hi.
I'm using nRF51822 with softdevice 8.
I started working with the uart example. and it works fine.
However, I can't get the BLE to reconnect automatically once the device...
Hello, i'm working with nrf8001 right now. I know that nrf8001 can work like Peripheral(slave) device. This is working ok. Im wondering if it is possible for nrf8001 to work...
Hello I'm trying to utilise the multiceiver mode with nRF24L01 and Arduino, the idea is that an nRF will be able to send a message and six other receivers will be able to...
When I use nRF UART of android phone A and B to scan the bluetooth device, the scan result is below:
first picture is the result of phone A, second is phone B:
first one...
