Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
Hi,
I'm using the mqtt_simple example to develop a new application.
I want you to tell me what lines of code I need to add for the nRF9160 to work in the minimum power...
Hi,
I am working with NRF52840 DK, from this i am using KEIL IDE. I got some error while opening the KEIL SW like Cannot set path to software packs. Make sure that RTEPATH...
Hi,
My customer use nRF5340 as their master control IC, which will connect with lots of peripheral.
They are considering about simulate a uart with GPIO.
What's the...
I have designed a custom board for the nrf52840 and upon testing it in the nrf connect sdk (using a JLink), I can only see the board when it's in bootloader mode. When it...
Hi,
I am in the process of migration from SES to Visual Studio; I have imported my project; but it has no active build configuration. When I try and add a build configuration...
I am using 9160 to develop a watch product. During the network test, I found that the description of parameter period tau in CPSMS instruction and xmonitor instruction is...
So, i have created a custom board using the nrf52811 SoC. I tried to upload some bluetooth examples to it, and i can see the device on the nRF connect APP. The problem is...
On firing the following command "$ node cli create-ca-intermediate"
terminal showing error
I am following this link nordicsemiconductor.github.io/.../DeviceCredentials...
Hi support team,
I'm trying to simulate the BDM protocol of the 9s12 chip series. Basically the protocol is as follows: Communication on 1 GPIO pin, output open-drain mode...
Hi,
NCS1.9.1, VSCode, nRF5340DK cannect a NFC tag,
i write text to NFC tag by Adafruit-PN532 with anouher device,
than 5340 mcu how to read the text in NFC tag ?
...
Hi! I would to know how to partition the memory of the board and how to make that secure and trusted. Once I did that there is a way to save some information in that portion...
I'm using a nRF52832 for a product under FAA regulations. The standard requires the BLE module to perform a self-test. What self-test capabilities does the Nordic nRF52 family...
Hi,
I see that the NRFX_SAADC_CONFIG_LP_MODE macro sets the default low_power_mode member for the nrf_saadc_config_t struct used to initialize the adc. What I cannot figure...
Hi Nordic Dev Team,
I've got an application where I want to store two types of log data in my memory flash that I want to send to server eventually via BLE mobile app. ...
Hello, I recently did a ble project, it requires pairing and binding ,
1， I can't find ble central demo
2, The ble central of 52832 will connect to multiple slaves, and...
