GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
I have two dev kit with nrf52833 one as a tag and other as anchor, the kits are made by Ublox and they demonstrate fine the direction finding functionality.
The problem...
I am using nrf52840 mesh v17.0.2 light_lightness server example.
In the original Light lightness server code, you can control LED1 using J-Link RTT Viewer. By sending...
I need my own input handler procedure that cannot wait.
Interrupt handler is directly attached as GPIOTE_IRQHandler (i don't use your libraries) and takes no more than two...
I am new to Nordic. I installed nRF Desptop Connector. I have opened succesfully the sample nRF projects. Now, I want create my own new nRF Connect Project. I tried two ways...
Hi,
I'm trying to set up a custom driver for the VL53L1X Sensor. (nRF9160 + Icarus Board + NCS 1.7.1)
I placed a new folder in drivers/sensor + modify CmakeLists.fr &...
Hi,
Our project team has decided not to using an external MCU to interface with the 9160 over the UART. So we'll need to write our application on nrf9160. The application...
P19 (Debug OUT Connector) on the nRF52840 BLE RF Development Board, PCA10056 (Dev Board) provides the ability to program a nRF52840 BLE board (BLE Board).
Questions:
...
Hi there,
Attempting to use the sample program for direction finding and have been following Case ID: 280319. Have attempted to add the code suggested by Simonr in adding...
Hi,
I'm working on a project using Zephyr and ncs 1.7.1. One of its functions is to stream WAV files from a SD card. It only ever reads data.
The issue I'm having is...
Hi all,
I am using SES in Win10. After I updated my NCS to 1.7.1, I failed to open my solution. However, it runs succussfully in SDK 1.6.1. The infomation is below:
...
Hello.
I am currently working on implementing a PWM control function using nrf52840. I used the function "es_battery_voltage_get()" to read the battery voltage before and...
I have written simple hello world code on nRF9160 custom board and enables the MCUBoot as bootloader using CONFIG_BOOTLOADER_MCUBOOT=y in prj.conf file.
Also, made some...
Hi everyone, I'm trying to communicate with OBDII through NUS using nRF52832. I was able to initiate the connection, send commands to OBDII, and get responses on the ECUsim...
The current RRC Inactivity Timer from my provider is 10 seconds, causing my power consumption in RRC Connected mode to be unnecessarily high.
I want to use the Release Assistance...
