Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello,
I have been evaluating the DECT NR+ physical layer with nRF9161DK boards with the v3.0.2 DECT Shell sample application. I am wondering if there are going to be any...
Hi Sir,
I have a question about these two configurations in overlay-ppp-cmux-linux.conf, CONFIG_MODEM_BACKEND_UART_ASYNC_RECEIVE_IDLE_TIMEOUT_MS and CONFIG_MODEM_BACKEND_UART_SLM_TRANSMIT_TIMEOUT_MS...
Hi,
I recently started working with the nRF9151 DK and was able to run the initial demo programs without any issues. To continue testing, I picked up a Thingy:91 X, but...
Good day, Nordic staff!
We are working on a product using the FLPR for its intended peripheral-controlling purpose. For us, the best way to send commands to and receive...
Greetings to everybody! There is some question about nRF54L15-DK board measured current consumption. I measure current via the P6 connector, that is, I measure current within...
Hi，
The same hardware and software have been in continuous production for several years without issues. However, the latest batch exhibited abnormally high power consumption...
Hi,
I am developing a small app for the nRF52840 using the SDK V3.1.0 and the Visual studio Code on a PC windows 11.
What I like to do is to be able with the app to change...
Hello,
I'm using the nRF5340 and have configured UART with EasyDMA to receive a variable number of bytes at 307200 baud. Our application has strict timing constraints, so...
To preface:
Board: nRF52840DK
OS: Windows 11
nRF Connect SDK / Toolchain: 2.9.0
VS Code Extensions:
nRF Connect for VS Code: v2025.5.152
nRF Connect for VS...
Hi guys,
I am currently working on a data migration of the settings storage to the external flash.
The problem I am facing is that after an OTA update, the device does...
A project I am working is proposed to have an nrf 5340 connected via UART to Yocto (Thud). Am looking for suggestions on an embedded client that will work with v3.0.0 of the...
We are using this custom baord to check the I2C addresses where the I2C BQ_SCL (P1.00) and BQ_SDA (P1.01) connects to various peripherals. However we are unable to get the...
Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
