Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
My project uses ESB for communication. In our hardware design, nrf5340 + FEM is used. Nrf5340 uses two GPIO link FEM chips to switch between PA mode and LNA mode. May I ask...
Dear Nordic,
I am considering to make a board that includes an nRF5340 + display. I am looking at a display that supports QSPI and I was wondering if the nRF5340 QSPI can...
Hi,
I am learning nRF52840 development and making a sensor device.
The datasheet of the nRF52840 chip says:
Regulated supply for external components up to 25 mA
...
Hi,
I'm working on a project with the Nordic nRF9160 Development Kit and am trying to send Bluetooth beacon data from the nRF52840 chip to the nRF9160 chip using UART and...
Hello,
I try to enable the LE Data Packet Length Extension. According to the available documentation, it should be as simple, as adding `CONFIG_BT_USER_DATA_LEN_UPDATE=y...
When loading empty software (zephyr based) into the nRF9151, the nRF9151 uses roughly 4mA and when erasing the IC, it uses 5.8mA.
Does zephyr not include a power down mode...
Hello!
I am porting a nRF Connect v2.9.0 application from a nRF52 to the nRF54L15.
We are using PPI/EGU to get exact measurements for some BLE radio events for some optimizations...
Hi,
We are developing application software on the nrf9161dk that uses the little FS file system running on external FLASH. Most of the application development has been completed...
Hi
I want to use P0.18 gpio as output pin and not as reset for nordic.
I am using ncs v2.0.0.
I have added
CONFIG_GPIO_AS_PINRESET =n in prj.conf
and when i...
Hello,
I have a Nordic Thingy:91, and I need to perform continuous wave (CW) transmission tests in LTE. To achieve this, I plan to develop custom firmware that alternates...
Hello Everyone,
We are working on a new product using the nrf52840 and OpenThread.Our current product uses the Azure IoT Hub and we were wondering if we could use the library...
Hi,
I defined __STACK_SIZE as compile/build flag. It has no effect according to GCC output after building is done.
Chip is nRF52840.
I tried to set fixed stack size...
Based on the message on the following page, nrfjprog has been deprecated and should no longer be used:
https://www.nordicsemi.com/Products/Development-tools/nRF-Command...
